Jump to content
SAU Community

Good Sydney Tuner

cul8er

By cul8er,
in Engines & Forced Induction

 Share

Recommended Posts

Deano 1 Mentor

Deano 1

Posted
Posted

JEM did wonders with my car,but like the guys above said,make sure all the little things are in good condition before you go otherwise youll have to pay them good $$$ to fix minor things>Remember time is money when dealing with any good tradesman,not just cars.They can also do a smoke test on the inlet system to find any leaks for a small fee.

jez does the smoke test for free, part of his pre dyno run checks before he runs it up.......

  • Replies 46
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Posted Images

Hadouken Grand Master

Hadouken

Posted
Posted

I'd be using DVS JEZ

Ahhhhh he said Sydney, i would say JEZ otherwise :)

drive to the coast, get jez to do it.... worth the drive, plus u get awesome freshly tuned thrashing on the freeway all the way home : D

Dvs tuning /thread

OLD PAC ?

jez does the smoke test for free, part of his pre dyno run checks before he runs it up.......

GTR_JOEY Grand Master

GTR_JOEY

Posted
Posted

This is the internet cupcake. Besides, you said unigroup or jez. So tuck your vagina in and accept it

Aren't we mouthy in front of our key boards and computer screens

Funny how confident little boys aren't in the real world :)

mattie4270 Rising Star

mattie4270

Posted
Posted

Come on guys,we are just trying to help this dude out.Conclusion,all the tuners mentioned are great,not cheap(cheaps a worry)When I first got my GTR the tuner I was recommended to was pathetic and expensive,no communication skills and treated people disrespectfully.As I said any of the guys mentioned above will do the trick.As I read one of your posts GTR JOEY, If you want to own a good GTR you need to have enough cash to buy two,very well said!

Hadouken Grand Master

Hadouken

Posted
Posted

Come on guys,we are just trying to help this dude out.Conclusion,all the tuners mentioned are great,not cheap(cheaps a worry)When I first got my GTR the tuner I was recommended to was pathetic and expensive,no communication skills and treated people disrespectfully.As I said any of the guys mentioned above will do the trick.As I read one of your posts GTR JOEY, If you want to own a good GTR you need to have enough cash to buy two,very well said!

You sound like a good guy

34GeeTeeTee Grand Master

34GeeTeeTee

Posted
Posted

Come on guys,we are just trying to help this dude out.Conclusion,all the tuners mentioned are great,not cheap(cheaps a worry)When I first got my GTR the tuner I was recommended to was pathetic and expensive,no communication skills and treated people disrespectfully.As I said any of the guys mentioned above will do the trick.As I read one of your posts GTR JOEY, If you want to own a good GTR you need to have enough cash to buy two,very well said!

My original tuner was a fkn retard! Shit tune, bad starting, poor fuel economy and much lower power than expected for the setup....

Went to JEM and have never been happier with the service, passion for cars and attention to detail... The guys are great!!

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The Bogan
      NC MX5

      By The Bogan · Posted

      I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • Kinkstaah
      From Japan and back to Europe, my sh*tbox R34 GTT

      By Kinkstaah · Posted

      You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
    • Dose Pipe Sutututu
      From Japan and back to Europe, my sh*tbox R34 GTT

      By Dose Pipe Sutututu · Posted

      LOL.... you are correct there.
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      It's been quite the ordeal but hey, at least you figured it out.
    • The Bogan
      NC MX5

      By The Bogan · Posted

      The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
×
×
  • Create New...