Jump to content
SAU Community

Recommended Posts

Hey guys long story short i have changed my radiator , thermostat , radiator hoses , radiator cap and water pump and since then my overflow bottle has gone bone dry 2 times and im freaking out as i have checked my oil cap and its not milky and the fact that i have basically changed the whole cooling system and this is happening.

has anyone else had this same problem or know what it could be cos from what iv seen i cant see any coolant leaking.

last time i filled it up when the overflow went empty, now yesterday the coolant had about 2 fingers left in the bottle and i had a looktoday and there is nothing left then i went filled petrol and have not checked the radiator yet

long story short i bought this car and it sat for 1 year as i was still on my ps and when i was getting a power steering belt changed i later on realised something must of hit the standard radiator and there was a hole so i swapped it out for a just jap one. upon getting my fulls i got it tuned there was a hairline crack in the water pump so that was swapped out and i thought id might as well do the thermostat as the rest of the cooling system was new

hey you bleed the cooling system of air... it could be just bleeding the air from the system and using the coolant from the overflow like it should.

cheers sam

system was bled and filled up after so i doubt it could be that.

If its not leaking on the ground then its probably going in a cylinder,most probably a head gasket.Check the spark plugs,if ones a bit chalky then thats the cylinder

coming to think of it i have had a really bad misfiring on idle so i will def give the spark plugs a check tomorrow

Could be air still working itself through the system keep on filling up and hope it stops, give it 5 more cold start-ups to be sure.

This happened to me, more then twice when i went for a drive checked the coolant in the morning and nothing was in the overflow

turned out my radiator cap was shot and no pressure was in my hoses (check for pressure in yours) changed it and 2-3 times after that it did the same

thing just not as bad and i just kept on feeling her up until coolant stayed. I reckon air still in the system ! i was afraid my head gasket or worse

cracked block was the problem, thank god it wasn't.

Edited by starwarz

poppedd in to my mechanics today he is leaning towards a air leak as when he put more fuel into the tune the car started to idle better.

so its going in next monday for a smoke test and a pressure test on the cooling system

thanks mate... this is the last thing i need now haha.. had car in lock up for a yr just watching it till i got my fulls and hopefully i dont need to watch it for another yr till i save $ to build the engine

It still needs bleeding there hard to bleed. I keep bleeding it then let it cool down and check overflow bottle until level stablizes takes close to 10 times til fully bled so nothing to worry about, either keep topping it up til it stops losing or bleed it.

Edited by boostn0199
  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
    • I suppose it was relatively stock too, the JZ motor handle most mods thrown at them without even breaking a sweat 
    • I saw your intro update, are you sure you've actually had a starter motor failure? You mention it could be the alarm causing it. I'm assuming you've got a no start issue, but what are the exact symptoms, as there could be a few reasons it has stopped wanting to start.
×
×
  • Create New...