Jump to content
SAU Community

Recommended Posts

The former is a halogen bulb intended to look like an HID.

The latter is an HID bulb.My knowledge of the V35 is hazy at best so I'm not sure if the OEM headlights are HID but if they are, then you'll need to have retained the HID ballast and retaining clip from the compliance conversion.

Link to comment
https://www.sau.com.au/forums/topic/408386-xenon-lights/#findComment-6515148
Share on other sites

I generally stick to the terms 'HID' and 'halogen'. Xenon is a bit ambigious as HIDs are filled with Xenon gas, but you can get halogens with traces of Xenon gas also.

So the term Xenon doesn't really define the type of lamp.

As Sean said, factory low beam are HID. If the car was complied proplery, they would have been removed and had halogens fitted. However there are plenty of V35s getting around still with their factory HIDs in tact, either re-fitted after compliance, or complied by a workshop that didn't know they need to be removed.

Link to comment
https://www.sau.com.au/forums/topic/408386-xenon-lights/#findComment-6515279
Share on other sites

I'm not really sure what it has at the moment as I'm not the first owner.. The left is working but the right has blown. Best bet would probably be to take the right one out and find out what it is hey? It has been checked for defects and what not when i brought it from Melbourne and they said nothing about them so maybe they are halogens?

Link to comment
https://www.sau.com.au/forums/topic/408386-xenon-lights/#findComment-6515777
Share on other sites

I generally stick to the terms 'HID' and 'halogen'. Xenon is a bit ambigious as HIDs are filled with Xenon gas, but you can get halogens with traces of Xenon gas also.

So the term Xenon doesn't really define the type of lamp.

As Sean said, factory low beam are HID. If the car was complied proplery, they would have been removed and had halogens fitted. However there are plenty of V35s getting around still with their factory HIDs in tact, either re-fitted after compliance, or complied by a workshop that didn't know they need to be removed.

I should hate stated xenon halogen aha apologies.

I'm not really sure what it has at the moment as I'm not the first owner.. The left is working but the right has blown. Best bet would probably be to take the right one out and find out what it is hey? It has been checked for defects and what not when i brought it from Melbourne and they said nothing about them so maybe they are halogens?

Go up to your headlight cover, and look at the bottom you will see little engravings it should say D2R. If you aren't sure, remove your front bumper and look for a ballast (a box with wires connected to it leading to the headlights) and read what is written on that. If you have a ballast, you have HID's and i believe if there is no ballast you have Xenon Halogens. It's a little confusing. My right headlight has blown too, i am planning on buying aftermarket lights but i need to take my bumper off and look for the ballast to see what will work with my car.

Goodluck!

Link to comment
https://www.sau.com.au/forums/topic/408386-xenon-lights/#findComment-6515784
Share on other sites

Uneducated response here, but don't HIDs take a half second or so to come on, while halogen would be instant on?

My low beams have a delay, and for that reason alone I believe they are HIDs. The high beams, which also emit a different colour light, come on instantly and I believe they are halogen.

Link to comment
https://www.sau.com.au/forums/topic/408386-xenon-lights/#findComment-6515940
Share on other sites

HIDs do have a smal delay, but the most noticeable effect is the don't come on at full brightness when cold, they take about 15 seconds or so to reach full brightness, and they tend to be a bit 'blueish' as they warm up.

Link to comment
https://www.sau.com.au/forums/topic/408386-xenon-lights/#findComment-6515972
Share on other sites

Just checked - my low beams are a blueish colour & highs are yellow. Lows have a very slight delay turning on from cold, and also take a few seconds to get to full brightness - as per sonicii but not 15 seconds, maybe 3-4. Highs come on instantly.

Link to comment
https://www.sau.com.au/forums/topic/408386-xenon-lights/#findComment-6516200
Share on other sites

Out of curiosity, since I haven't converted my lights back to their original HIDs, I have noticed that my high beams don't seem to have as much reach as they probably should. I keep the AFS switched off to avoid the AFS alarm from the lamps not being able to swing at all since the conversion and to obviously avoid any mechanical damage as a result. Do our headlamp assemblies start in the lowered position perhaps and that's why my high beams aren't really pointing high up like they should?

Link to comment
https://www.sau.com.au/forums/topic/408386-xenon-lights/#findComment-6516319
Share on other sites

Hey guys just a few quick questions - I have removed my headlights and I have halogens, but there are little grey units with yellowish stickers bolted onto the bottom of the headlights with wires coming out of them (cut wires), is this the factory hid unit? If so how would I go about setting it up? Is it difficult? Are there any diy's?

Link to comment
https://www.sau.com.au/forums/topic/408386-xenon-lights/#findComment-6516587
Share on other sites

Just checked - my low beams are a blueish colour & highs are yellow. Lows have a very slight delay turning on from cold, and also take a few seconds to get to full brightness - as per sonicii but not 15 seconds, maybe 3-4. Highs come on instantly.

So you have HID low beams and the top lights are Halogen :)

Hey guys just a few quick questions - I have removed my headlights and I have halogens, but there are little grey units with yellowish stickers bolted onto the bottom of the headlights with wires coming out of them (cut wires), is this the factory hid unit? If so how would I go about setting it up? Is it difficult? Are there any diy's?

Does it look a little something like this? If the wires are cut and not connected to anything, someone has been lazy and left the HID ballast in there. It might not be in use, but if you get the appropriate bulbs to suit HID bulbs and the wiring you need you can try hook it up but do a bit of research first. G35driver.com is a great forum with loads of info on pretty much anything and everything to do with these cars, give it a shot.

n3b4b8.jpg

Link to comment
https://www.sau.com.au/forums/topic/408386-xenon-lights/#findComment-6516735
Share on other sites

Yup looks like the one in the pic.

So all I need is the wiring and globes?

Would these fit?

http://www.ebay.com....=item27c0ff9d43

Thanks

Correct, and obviosly you have to make sure the other end of the ballast is connected to something lol.

You have to be careful with D2R and D2S they use different bulbs.

Edited by Seano350GT
Link to comment
https://www.sau.com.au/forums/topic/408386-xenon-lights/#findComment-6516996
Share on other sites

are you sure they are different? All the ones I've found on ebay say d2r d2s and even d2c!!

http://www.ebay.com.au/itm/Nissan-350Z-Murano-Subaru-WRX-STI-D2S-D2R-Factory-Xenon-HID-Replacement-Ballast-/170720897409?pt=AU_Car_Parts_Accessories&hash=item27bfc22981

Even that says d2r d2s ^

I'm so confuse :(

Link to comment
https://www.sau.com.au/forums/topic/408386-xenon-lights/#findComment-6517001
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...