Jump to content
SAU Community

Recommended Posts

I am seriously feeling depressed after selling my r33 gtst :( kind of regret it but oh well.

Sold it due to me wanting an R33 GTR.....is the upgrade to a GTR that much of a difference?

be honest lol.

Edited by BOOSTBIG
Link to comment
https://www.sau.com.au/forums/topic/408403-sold-gtst-for-r33-gtrworth-it/
Share on other sites

man, based on what you know, and what you see....i think it'll be chalk and cheese.

i've never owned a GTR, but just look at the facts;

2.6 vs 2.5

different heads,

turbos,

TRACTION!

and many other engineering variables.

Go for a test drive in one, and see for yourself, and make up your own opinion of what a GTR is.

Peace out! :woot:

I sold my GTST ages ago to buy a GTR, it's worth it.

Since I've had 3 GTR's with plans to buy another GTR despite my trying to get something else.

Ok thanks heaps guys.

any advice or things I should know about before I purchase a gtr?

any particular model? I am after the R33, but do they differ in terms of specs depending on the year model?

and any difference between a standard gtr and v spec?

thanks guys

You'll just love the R33 GT-R Chris :)

*The V-Spec has a quicker ATTESSA System to activate the front wheels.

*V-Spec is easily recognised by the fins on the rear diff.

*Besides checking for any rust (indicating that the car has lived much of its life near the Japanese coast or been driven on salted roads), do your usual checks as you would on any car.

*I would look for complete history from here as well as Japan &/or receipts.

*Wear and tear should be consistent with the odometer; including driving seat bolster, scratches on steering wheel as well as sun damage, scratches on ignition barrel, scratches under driver's door handle, scratches on door sill, gear knob condition (but that's often changed anyway), and ageing of the windscreen wiper arms.

*Electrics are usually good on the R33 GT-R.

*Brakes should be fine also, but need checking if tracked very much

*Do slow circles clockwise and anticlockwise with windows down to listen for CV clicking

*Check where the car is usually parked overnight to see if there are any oil drips. But put it up on a hoist anyway to check seepage

*Compression test is recommended

*Series II will have 2 airbags & later models may have Xenon headlights

*Don't be surprised about different quality rides in different GT-Rs since there is a wide variety of coilovers out there with different spring rates and settings

You'll just love the R33 GT-R Chris :)

*The V-Spec has a quicker ATTESSA System to activate the front wheels.

*V-Spec is easily recognised by the fins on the rear diff.

*Besides checking for any rust (indicating that the car has lived much of its life near the Japanese coast or been driven on salted roads), do your usual checks as you would on any car.

*I would look for complete history from here as well as Japan &/or receipts.

*Wear and tear should be consistent with the odometer; including driving seat bolster, scratches on steering wheel as well as sun damage, scratches on ignition barrel, scratches under driver's door handle, scratches on door sill, gear knob condition (but that's often changed anyway), and ageing of the windscreen wiper arms.

*Electrics are usually good on the R33 GT-R.

*Brakes should be fine also, but need checking if tracked very much

*Do slow circles clockwise and anticlockwise with windows down to listen for CV clicking

*Check where the car is usually parked overnight to see if there are any oil drips. But put it up on a hoist anyway to check seepage

*Compression test is recommended

*Series II will have 2 airbags & later models may have Xenon headlights

*Don't be surprised about different quality rides in different GT-Rs since there is a wide variety of coilovers out there with different spring rates and settings

thank you so much for that post man. appreciate it.

do you guys recommend I put in forged pistons as soon as possible?

thank you so much for that post man. appreciate it.

do you guys recommend I put in forged pistons as soon as possible?

You'll only need forgies if you're chasing some big power (300ish at the wheels).

You're probably best waiting until the donk needs a rebuild before you go to that expense.

Don't let me stop you but you're looking at a sizeable bill even if you can do it yourself.

Personally I'd work up to it. Mine came with them so happy days!

Could be worth looking for one that has already had engine work. What has been spent on top of the value of the car will be waaaay less than what it would cost you to get done.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yea that’s why I said ima test them with multimeter and see the reads.
    • Only at idle. Isn’t a problem when rev it seems.
    • @Haggerty This seems silly to ask, but are you confident in your ability to tune the Haltech?  
    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
×
×
  • Create New...