Jump to content
SAU Community

Tein Type He Difference Between Models

Don Dada
 Share

Recommended Posts

Don Dada Mentor

Don Dada

Posted
Posted (edited)

Guys, I have a set of Gold S15 Tein drift spec, winding master Type HE on my car right now and one of the rear has started to leak.

I also have a spare one of the same winding master Type HE from a previous vehicle but its ECR33 spec

The spring for the R33 is visibly longer and thicker, otherwise everything is identical, but I'm not sure if the valving is the same between the two, and Tein just fitted it with different springs to suit the specific vehicle

It would be great if i could just swap springs and go again!.....What do you guys think?

Edited by Don Dada
Hank Scorpio Grand Master

Hank Scorpio

Posted
Posted

The valving will be different for the different spring rates.

If you were keen take it into a suspension shop with a shock absorber dyno and get the two shocks dyno'd together to see the difference. You might find that the S15 on full hard dampening is equal to the R33 on 8-clicks dampening or something similar.

AngryRB Grand Master

AngryRB

Posted
Posted

is it possible to replace the springs on some Ha Tein coilovers inorder to make the suspension more street friendly and not rock hard, my coilovers even on soft are still hard...

GTSBoy Grand Master

GTSBoy

Posted
Posted

Well, yeah. They take standard sized springs don't they? That's part of the logic behind coilover you know.

The only problem with that concept is that the damping might not be adjustable enough to cope with big changes in spring rate without being dismantled and revalved.

Hank Scorpio Grand Master

Hank Scorpio

Posted
Posted

Dropping spring rates by about a kg here and there should be fine for the shock absorber to cope with but as GTSBoy said you don't want to change it too much because those shock absorbers are valved for those specific sopring rates.

AngryRB Grand Master

AngryRB

Posted
Posted (edited)

Well, yeah. They take standard sized springs don't they? That's part of the logic behind coilover you know.

The only problem with that concept is that the damping might not be adjustable enough to cope with big changes in spring rate without being dismantled and revalved.

I dont know anything about standard springs, but yeah they seem just a bit on the hard side, was thinking they must be possibly a 12kg spring, so if dropping them to a 10kg was possible it would make the ride better, and aid in the launches at the drags although i may opt for some old stock rear suspension for that..

have 18inch wheels is obvioulsy not helping to cushion the bumpy rough roads, guess its a bit of a take the good with the bad, on a mostly smooth road its perfect..

Edited by SliverS2
GTSBoy Grand Master

GTSBoy

Posted
Posted

When I said "standard" I meant "standard size and fitment" - for a coilover. As in, across a wide range of manufacturers, they all use 60mm diameter (or whatever it actually is) and the same top and bottom shape so that you just buy springs - you don't have to buy X springs for X brand coilover. You buy whatever rate spring you need.

Miguelone Grand Master

Miguelone

Posted
Posted

Plenty of brands do replacement springs in your desired spring rate as well. Eibach, Tein, Swift etc. Most coilover manufactures will also let you specify different spring rates to standard when ordering coilovers so what you may have might be stiffer/softer than what the coilover is speced with generally.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      I myself AM TOTALLY UNPREPARED TO BELIEVE that the load is higher on the track than on the dyno. If it is not happening on the dyno, I cannot see it happening on the track. The difference you are seeing is because it is hot on the track, and I am pretty sure your tuner is not belting the crap out of it on teh dyno when it starts to get hot. The only way that being hot on the track can lead to real ping, that I can think of, is if you are getting more oil (from mist in the inlet tract, or going up past the oil control rings) reducing the effective octane rating of the fuel and causing ping that way. Yeah, nah. Look at this graph which I will helpfully show you zoomed back in. As an engineer, I look at the difference in viscocity at (in your case, 125°C) and say "they're all the same number". Even though those lines are not completely collapsed down onto each other, the oil grades you are talking about (40, 50 and 60) are teh top three lines (150, 220 and 320) and as far as I am concerned, there is not enough difference between them at that temperature to be meaningful. The viscosity of 60 at 125°C is teh same as 40 at 100°C. You should not operate it under high load at high temperature. That is purely because the only way they can achieve their emissions numbers is with thin-arse oil in it, so they have to tell you to put thin oil in it for the street. They know that no-one can drive the car & engine hard enough on the street to reach the operating regime that demands the actual correct oil that the engine needs on the track. And so they tell you to put that oil in for the track. Find a way to get more air into it, or, more likely, out of it. Or add a water spray for when it's hot. Or something.   As to the leak --- a small leak that cannot cause near catastrophic volume loss in a few seconds cannot cause a low pressure condition in the engine. If the leak is large enough to drop oil pressure, then you will only get one or two shots at it before the sump is drained.
    • GTSBoy
      Help! Leak coming under transmission

      By GTSBoy · Posted

      So..... it's going to be a heater hose or other coolant hose at the rear of the head/plenum. Or it's going to be one of the welch plugs on the back of the motor, which is a motor out thing to fix.
    • MBS206
      Mistakes were made, my R34 Story

      By MBS206 · Posted

      The oil pressure sensor for logging, does it happen to be the one that was slowly breaking out of the oil block? If it is,I would be ignoring your logs. You had a leak at the sensor which would mean it can't read accurately. It's a small hole at the sensor, and you had a small hole just before it, meaning you could have lost significant pressure reading.   As for brakes, if it's just fluid getting old, you won't necessarily end up with air sitting in the line. Bleed a shit tonne of fluid through so you effectively replace it and go again. Oh and, pay close attention to the pressure gauge while on track!
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      I don't know it is due to that. It could just be due to load on track being more than a dyno. But it would be nice to rule it out. We're talking a fraction of a second of pulling ~1 degree of timing. So it's not a lot, but I'd rather it be 0... Thicker oil isn't really a "bandaid" if it's oil that is going to run at 125C, is it? It will be thicker at 100 and thus at 125, where the 40 weight may not be as thick as one may like for that use. I already have a big pump that has been ported. They (They in this instance being the guy that built my heads) port them so they flow more at lower RPM but have a bypass spring that I believe is ~70psi. I have seen 70psi of oil pressure up top in the past, before I knew I had this leak. I have a 25 row oil cooler that takes up all the space in the driver side guard. It is interesting that GM themselves recommend 0-30 oil for their Vette applications. Unless you take it to the track where the official word is to put 20-50w oil in there, then take that back out after your track day is done and return to 0-30.
    • PranK
      My new to me M35 Stagea wagon

      By PranK · Posted

      Nice, looks great. Nice work getting the factory parts also. Never know when you'll need them.
×
×
  • Create New...