Jump to content
SAU Community

Damaged Coilpack Electrodes


sev
 Share

Recommended Posts

The ends of my coilpacks are damaged, i.e the carbon ends on the end of the spring,

2 Questions,

1: Whats causes this?

2: Is there anywhere i can get replacements, as i dont really have the cash to buy a new set of coilpacks.

All coilpacks tested between 0.7 and 0.9

Its an rb20 gts4.

Thanks in advance.

Link to comment
Share on other sites

Yeah that looks to be whats happened. I believe they are meant to have like a dome tip, but as mine have cracked away, they are far from it. I should really have got a picture. Im worried if i get new ones for somewhere, the same will happen again. Is there a problem elsewhere?

Link to comment
Share on other sites

I've no idea how many k's are on them, however the car is on 120k's and they have been replaced at some point, as they have rb25 written on the side of them in paint pen.

Am i looking at general wear and tear, or have i got a problem?

Link to comment
Share on other sites

Sounds like general wear and tear. I've seen them do this before.

But i dare say being rough with them, ie dropping them, ramming them onto the plug would cause cracking issues.

I doubt you'll have much luck finding new electrodes.

Link to comment
Share on other sites

I've no idea how many k's are on them, however the car is on 120k's and they have been replaced at some point, as they have rb25 written on the side of them in paint pen.

Am i looking at general wear and tear, or have i got a problem?

If they have RB25 written on in paint then they were second hand replacements. Did they still work? You need to be saving for a new set.
Link to comment
Share on other sites

Hi Sev.

Those carbon tips are not used anymore on the new coils, They just have springs.

What you could do is clean the tips up on some sand paper and stretch the spring a bit, to make a good contact.

If that doesnt work i can send you a new set of spring ,(free) as i sell nissan RB coil packs and have some spares

Send me your address details if you need them.

Cheers,

Clive

Link to comment
Share on other sites

Hi Sev.

Those carbon tips are not used anymore on the new coils, They just have springs.

What you could do is clean the tips up on some sand paper and stretch the spring a bit, to make a good contact.

If that doesnt work i can send you a new set of spring ,(free) as i sell nissan RB coil packs and have some spares

Send me your address details if you need them.

Cheers,

Clive

I'll have a look at cleaning them up, it was a couple of weeks ago and i've slept since so i can't remember how bad they are, i just know they wont sit flush with the top of the spark plugs.

Thanks, I'll get back to you

Sounds like general wear and tear. I've seen them do this before.

But i dare say being rough with them, ie dropping them, ramming them onto the plug would cause cracking issues.

I doubt you'll have much luck finding new electrodes.

Good, i just didnt want to hear it was this or that that needed replacing at $$$

If they have RB25 written on in paint then they were second hand replacements. Did they still work? You need to be saving for a new set.

Yeah thats what i thought, probably from a scrapyard or something, but yeah they all test ok.

Cheers for everyone's help

Link to comment
Share on other sites

the coil ends of my coil packs are all burnt out and gone, running fine on 15psi gapped to 0.8 with no missfire / spluttering.

put in a spare set about a year ago with nice looking coils etc and car was missfiring and spluttering all over the place so just goes to show you cant just judge them on just how its looks

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share



  • Similar Content

  • Latest Posts

    • Took a little trip  went to nismo hoping the get my fuel tank hoses and unfortunately they told me they didn’t have stock luckily I was able to go to a Nissan parts store and they were able to order them in for me  then can home and cleaned the tank with some degreaser and fitted the new hoses before putting it back in the car 
    • 100% I’ll hack into the 33. Strap a turbo onto the RB25DE and/or put the 25 head on a 30 block. 33 passed in cos the reserve was too high. I’ll try lowballing it again and negotiate. Aim is to have it landed and on the road for under 15k, then spend the same amount on top in mods.
    • It's generally best practise to run 1x run without VCT enabled, then 1x run enabled till redline. Overlay the two torque graphs and you'll find the desired RPM to turn off VCT. Sometimes, it might be even worthwhile turning off VCT earlier control torque/cylinder pressure and using VCT purely to spool the turbo.
    • They sell them in Malaysia for about $4
    • First time I ever have issues with Amazon, but my wife often tells me to keep an eye out for fakes. It finally got me. I wrapped up the conversation with Gates. The gentlemen I was talking to seemed to hate his job but the response time on their technical support is outstanding. He stated that the hose is marked with some variation of "SAE J30R10" but that if you only purchase a 1 foot length like I did, it is possible to get a cut between markings and have a blank hose. To no ones surprise, he stated the swelling and "gummyness" isn't normal and to replace/buy from somewhere else (He mentioned NAPA). I'll toss a small end of the new one in gas for a few days before pulling the hanger out again, just to be safe.  Hose should arrive Monday. For those running multiple pump in tank hangers, you know the joys of getting them out and back in. I'm surprised I haven't destroyed my level float yet.  Lastly once I wrap all of this up, I'm planning on hitting the dyno again in 2 weeks while I'm on vacation. I realized recently that my VCT is set to turn off at 5000RPM. I'm surprised it wasn't increased while I was on the dyno last. I'm expecting I can increase it to ~6500RPM, if not more. Should hopefully get another 15-20kw out of it. I also want him to revisit my knock thresholds. I'm occasionally getting false knock around 3000rpm. 
×
×
  • Create New...