Jump to content
SAU Community

Recommended Posts

i just had Yokohama A539's fitted, and they seem to work very adequately. No slip in wet/dry at all yet. at $212 (now 199, grrrr) they were pretty reasonable i thought.... well, compared to Sava Intensa's they are fantasitc, but what do you expect?

Goodyear F1's are the worst tyres in the wet, they grip well when they're cold in the wet, but once they warm up you'll be sliding all over the place. They also tramline pretty bad.

Federal Tyres is developed by Sumitomo Rubber Industries Ltd. Japan

Latest Goodyear Eagle F1 have a AA wet braking rating and seem pretty good compared to the others I have used on the rear. Also Continental SportContact on front were good at my last race with nice feel and predictable breakaway. I pay $100 per tyre so go through them quick with an agressive setup. Combination was better than Pirelli P6000

All in 17's 235 front and 255 rear

thanks for the replies guys. at the moment i'm looking at the bridgestone SO series and the Toyo. As it being for my stock 15" i wouldn't wanna spend much on it cause i might swap it later for 17" when i get the money together. So yea my budget would be no more than around $120 - $130 per tyre. Have anyone use the Maxis MAV1, is that any good?

Cheers

I have a set of Goodyear Eagle F1 GS-D3's on my GTR at the moment. Done about 7,000kms on them and they are wearing very well. Don't know what funky is on about though, from my experience they are awesome in the wet regardless of how hot they are. Very confident of them in the wet, never feels slippery or aquaplaney.. They do tramline a bit, but I think most tyres over 245 size do that to a degree, GTR's i've heard are notorious for it too...

They are exxy but I was given wrong info on load ratings when I was looking which dictated me getting expensive tyres.. Still I'm more than happy with them..

Brett

The Eagles are good while straight driving in the wet, however when cornering they don't grip as well as my current tyre a set of Michelin Pilots. When cornering the Eagles tend to make the back slide a lil bit more than the Pilots. I have a S bend at the end of my road which I go thru at about 45 in the wet and about 60 when dry usually. The Eagles require a lot more control than the Pilots where I can trust the tyre to grip.

I still have Eagles on the front tyres and Pilots on the back, so far this set up I've found to be the best, the Pilots weren't as good as the Eagles on the front tyres... I don't know why.

I based the Eagles not working too well when hot on the fact that under heavy braking they'll grip for a while (5 seconds) then screech like crazy. After that every time I did any heavy braking they refuse to grip (I assume because they are now hot).

EVLR33, your friends are on crack.

I've done hillclimbs, cruises, autokhana's etc with 540's and they are brilliant, especially when on heat. Hell we even did Targa on 540's in 2000 and they were fantastic. As for tread, ever seen a new 540? tons of it :D

Not having a dig but those views you posted go against everyone elses i've heard on them

Can only go by what I'm told, and yes they are apparently pretty awesome in the dry, but as I said a few people I know aren't as happy about the wet weather performance. Personal opinion I guess differs greatly regarding what people class as good or bad performing tyres..

Regarding the tread, i meant that it's pretty much a slick tyre with a few grooves cut into it, nothing like a conventional wet weather tyre. And because of that I assumed they wouldn't be so great..

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...