Jump to content
SAU Community

Recommended Posts

Good move, I don't regret installing it for one second.

The other great benefit is that the sensor will be installed in the correct location in the exhaust. This will give you a more accurate reading of the AFRs (when you get it tuned) rather than a sniffer in the tail pipe.

  • 4 months later...

I've done a fair bit of maintenance to fix a few ongoing issues over the last few months. The car now has all the rubber suspension bushes replaced with Whiteline/Nothalane. It also has a new air conditioning condenser, heater core and rear wheel bearing replaced.

Of note, my car has had an intermittent steering wheel vibration at around 100 kph, that I've been living with for as long as I can remember. It wasn't because of a wheel imbalance as I've had several tyres/rims over that period with the vibration always persisting. What fixed the problem was replacing the front inner/lower suspension bushes. My upper camber and caster bushes had been swapped swapped out for urethane years ago - so the lower ones were the last rubber ones remaining.

  • 7 months later...

Time for some updates... Pics of the new Aircon condenser and Heater Core that I put in...

IMG_1573_zpsaab65d22.jpg

IMG_1574_zps766dd430.jpg

I ended up reusing the plastic heater core fittings not the metal ones shown in the picture.

  • Like 1

I found that the bolts and washers that hold my MX Performance plenum top down onto the lower runners weren't really up to the task and the washers had deformed. So I ordered some titanium flanged hex head bolts to replace them.

IMG_2017_zps80d277c5.jpg

Out of interests sake, I wanted to know the weight saving, seemed like a good job for the wifes Thermomix!

IMG_1969_zps684c5b51.jpg

IMG_1971_zpsc461a104.jpg

So for around $100 thats an awesome weight saving of 100 grams! I'll only need to spend another $500,000 on titanium bolts and I should be able to get the weight of my car down to the same as a Lotus Elise! :blink:

Edited by Ryno

Since going to my new exhaust manifold setup the car has been a fair amount louder. I finally decided to tackle it back in November and swapped out the rear cannons and centre muffler with new Magnaflow mufflers.

Out with the old...

IMG_1973_zpsec5a538e.jpg

Rigging up the new...

IMG_1975_zpsc8a4337a.jpg

IMG_1978_zps50c15af8.jpg

IMG_1979_zps363a85dd.jpg

My latest drama to fix was a leaking Power Steering rack...

IMG_2464_zps1b042f11.jpg

I was able to swap it for a reconditioned rack that cost $350. But at the same time I wanted to finally fix a problem that has been bugging me for around 10 years!

Ever since swapping to the RB25DET engine and removing the HICAS I've been living with heavy steering as the power steering goes into a limp mode due to no speed input.

The solenoid on the power steering rack gives full assistance with 12 volts and the assistace reduces as you reduce the voltage. So I purchased this voltage step down module from Jaycar...

IMG_2482_zps433531ac.jpg

I have wired that direct to the Power Steering solenoid and can adjust the voltage as I see fit. It is still not going to be speed variable (like stock) however I can tweak the voltage to find a happy assistance that works ok at all speeds.

Checking the output voltage...

IMG_2483_zpsb87539a7.jpg

Where I've mounted it in the car...

IMG_2484_zpsd066444c.jpg

Edited by Ryno
  • Like 2

Thanks Glyn, yeah I'm very happy with the exhaust... it looks the business and the sound has reduced nicely while still maintaining the unique note from the twin pipe setup.

Edited by Ryno

Yes I've been driving it to work every day this week. At the moment I have it set on around 8 volts and the steering is nice and light.

I'm just a bit frustrated that I've only fixed it now... It's such an easy solution, why the hell did I put up with crap steering for 10 years!?

  • Like 2
  • 2 weeks later...

Yes I've been driving it to work every day this week. At the moment I have it set on around 8 volts and the steering is nice and light.

I'm just a bit frustrated that I've only fixed it now... It's such an easy solution, why the hell did I put up with crap steering for 10 years!?

hey ryno

i have a 93 r32 gtr that still has hicas but occassionally has heavy steering at low speeds/parking. Can the above solution you put in place be useful for my situation?

Jase

Absolutely... all you are doing is intercepting and controlling the voltage going direct to the power steering rack. It's a very simple and effective fix.

fantastic ill keep it in mind if it continues to play up. Its been bugging me. Would you consider doing a diy write up?

fantastic ill keep it in mind if it continues to play up. Its been bugging me. Would you consider doing a diy write up?

I've just done up a DIY for the power steering fix, once it is approved by the moderators I will provide a link.

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...