Jump to content
SAU Community

Recommended Posts

Here is my pride and joy for expressing of interest at this moment. 1993 model in Burgundy colour.

KMs: 113000kms.

Mods:

2860-5 turbos

Walbro fuel pump

Nismo 600cc injectors

splitfire coilpacks

HKS camgears

grex oil cooler

Trust oil sump.

tomei oil restrictors

Power FC with hand controller

HKS boost controller

Extreme twin plate clutch

Original Nismo seats in perfect condition.

Alloy radiator.

Custom made oil catch can by Silverwater Automotive

Carbon shielded airbox

Nismo N1 headlights with HID kit installed.

Brand new Optima AGM dry cell battery with 800cca just put in.

HPI clear timing belt cover.

Braided water and oil lines on turbos.

Atezza switch between AWD and RWD

The bad:

Dash light is on and off which might be bad connection behind. I haven't really had time to take it out to check.

No A/C, condensor was taken out to fit the large oil cooler.

The car is in very good condition for an r32. Not a single bit of rust underbody, in the boot or in the engine bay, or even on any panels. Interior wise, a little wear and tear on steering wheel and shift boot. Dash condition is immaculate with absolutely no bubbles on the passenger side. Car is dead straight and drives dead straight.

Power: 330awkw @ 21psi on high boost

309awkw @ 19psi on low boost

Note: Power made with gtr AFMs. But they are at their max so Z32 AFMs are the option for more power out of this setup.

No asking price as this is a pure EOI. Offers are welcome.

Photos:

Photos:

264766_10151013675541121_799001671_n.jpg

319458_10151018188741121_1461797509_n.jpg

377090_10151018189726121_367795330_n.jpg

Edited by G0Z1LLAAAAA34
Link to comment
https://www.sau.com.au/forums/topic/409736-syd-1993-r32-gtr-~eoi~/
Share on other sites

Opps forgot to add:

Genuine Bilstein coilovers

Nismo front pipes followed by 3 inch cat back

Large 2 piece front brake rotors (Brand unknown, they came with the car when I bought it)

More technical bit:

Knock: 25-35 shown on FC hand controller on high boost setting

Injector max duty: 68-70% under full power on high boost setting

Edited by G0Z1LLAAAAA34

oops, you also forgot to add the price

read the rules

I don't know if you understand what express of interest means......This isn't an official for sale add so no price needed in the thread.

He is asking $16500 on JDMST.

And I don't know which GTR you are referring to. Read my jdmst thread again and see if there is a price on it....

Did you tell him he's dreaming?

I don't know what dreams you are having but i am certainly awake if you haven't noticed :)

Edited by G0Z1LLAAAAA34

No money owing. No major accidents. The chassis is accident free. I think a couple of panels have been repainted before I purchased the car as we can expect from a r32 gtr this age.

Edited by G0Z1LLAAAAA34
Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...