Jump to content
SAU Community

Recommended Posts

  • Replies 46
  • Created
  • Last Reply

Top Posters In This Topic

I just don't have the time to write up the guide, plus it may be a little confusing as it isn't an m35.

Che?

What do I drive? :P

Apologies for not putting up the comparison data, not so good with Excel so will take some time.

Excellent mod though and one of the first that should be done on a VQ25/VQ35 IMO

Che?

What do I drive? :P

Apologies for not putting up the comparison data, not so good with Excel so will take some time.

Excellent mod though and one of the first that should be done on a VQ25/VQ35 IMO

A tractor usually. :P

I forgive you Cam.

Is this the same principal: http://www.conceptzperformance.com/Cart/description.php?II=3434&Car_Type=G35&UID=20121009182338150.101.79.229

Of course I don't think it'd fit on a VQ25DET but sounds like the same concept.

Same concept, without the thermostat, and they didn't fixing the air bleed issue. That is the pathfinder coolant mod, I imagine that assembly will hold air in the thermostat too.

Mine also replaces the stock plastic bleed point with a billet alloy body and high pressure ball valve.

Is this the same principal: http://www.conceptzp...8150.101.79.229

Of course I don't think it'd fit on a VQ25DET but sounds like the same concept.

I looked at for some time Ryan and asked if it was bolt on and what, if any mods needed to be made to install.

The response?

"It is bolt on. It bolts onto the rear of the engine but you will have to cut and weld the pipe to attach to your coolant pipe"

(referring to the male/female fitting into the pipe on the driver side of the engine)

American "bolt on" is not the same as Japanese "bolt on". :no:

"It is bolt on. It bolts onto the rear of the engine but you will have to cut and weld the pipe to attach to your coolant pipe"

(referring to the male/female fitting into the pipe on the driver side of the engine)

American "bolt on" is not the same as Japanese "bolt on". :no:

What?

Don't think its weld on. The original piece for my car (dunno about NM35s) has a female end, and the goldy coloured anodised piece pushes in and secures into the alloy pipe.

The kit seems to have a lipped edge- so it wouldn't push in, but a bit of silicon tube and a couple of clamps would sort it out just fine.

I think the bigger issue is the cross over exhaust manifold pipe, and the extra stuff round the back there.

I like how their kit "lowers temps by 20 degrees", when I read that... The temps are still controlled by the stock thermostat ffs.

Ours is the same female fitting Alex, but the cast alloy pipe is a different shape for that reason, it would hit the crossover I think. ^^

OK, no steak knives please ... I am a vegetarian!

But I do have a relatively standard 2001 stagea and my Galaxy series 2 phone takes good pics so I am interested.

Also as a noob who took a long time to do the brake wire cut simply because I couldn't find pics I think its important to have good visual guides up here. Yeah Yeah I didn't take the pics either... next time I have the glove box out and on the back seat I will do a step by step on the 'brake wire snip' for new noobs. If you don't send me steak knives and do talk me through it, I'll do the same for this. :rolleyes:

You need a 2nd person to take the pics, otherwise the camera gets covered in oily fingerprints. :P

I have ordered the fittings, they should be around a week away. When they arrive I will have 3 kits ready to send out straight away. For anyone else interested I can make them up as I go.

You need a 2nd person to take the pics, otherwise the camera gets covered in oily fingerprints. :P

I have ordered the fittings, they should be around a week away. When they arrive I will have 3 kits ready to send out straight away. For anyone else interested I can make them up as I go.

Dibs!

  • 4 weeks later...

I'm going to try and fit this kit up on the weekend. Would I be right in saying it'll take an hour or two to remove the plenum and get down to the middle of the V to fit the top plate, about half an hour to actually fit the kit, and an hour or so to put it back together?

Should be about right. You shouldn't have to disconnect the fuel rail from the lines, just flip it over onto the drivers side guard.

Make sure you silicone the top plate, you don't want it leaking...

Shouldn't need to silicone it.

We used a new gasket for each of ours although the existing gasket would probably be good enough.

Gasket is the same as on a VQ35 in case you want to grab one from Nissan, Ryan.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
    • My wild guess is that you have popped off an intake pipe....check all of the hoses between the turbo and the throttle for splits or loose clamps.
    • Awesome, thanks for sharing!
    • To provide more specific help, more information is needed. What Android screen? What is its wiring diagram? Does the car's wiring have power at any required BAT and ACC wires, and is the loom's earth good?
    • So, now all you need to do is connect the 2 or 3x 12v feeds into the unit to permanent 12v, ACC 12V and IGN 12V that you can find in the spot behind the stereo, and the earth, and then it will switch on with the car.
×
×
  • Create New...