Jump to content
SAU Community

Recommended Posts

Hi all,

wondering if anyone has anything similar occur....

Basically on startup, the power steering is very noisy but then goes away once the car has warmed up.

The power steering pump has had a full reco around 18 months ago. Before then, the noise was constant.

Any help would be greatly appreciated.

cheers

Is the fluid aerated/bubbly in the reservoir?

100% its p/s? Dropped the belt and rechecked ?

Would suck if say it was an idler or tensioner pulley and just sounded like it was coming from p/s pump area then let go

Not sure, it's just really strange that on a cold morning startup the car is fine, no noises. If right then I do a dry steer, the loud noise starts. Once the car has warmed up a bit, it's all perfect and quiet!!! What the!!

  • 10 months later...

Not sure, it's just really strange that on a cold morning startup the car is fine, no noises. If right then I do a dry steer, the loud noise starts. Once the car has warmed up a bit, it's all perfect and quiet!!! What the!!

Pulling this up from a year ago but did you ever fix this problem....mine started doing this exact same thing this morning :(

this was the symptom of mine as the power steering pump was getting on - noisy when cold and dry steering, then would go away.

it will gradually get worse if it is indeed the PS pump.

bottom line is you can leave them for a while without any trouble.

Mine started having a noticeable effect on the slow speed steering when the car was still warming up until I did anything (replaced the PS pump).

good luck!

You can try replacing the fluid to help with cold temp steering. As fluid gets old and sludgey and is thicker than normal when cold. This means it isn't lubing the system as well. Draining the fluid and replacing it with fresh fluid can help.

I have to get around to doing it to my Commodore at some point (when I could be bothered, along with finding the cause of the slight misfire it has). had a leaky pump for ages and had put some stuff in it that was supposed to slow/stop leaks. Basically it was a thick fluid. I finally got a new pump but didn't completely flush the system (just topped it up really), so on cold mornings the steering has a bit of a notch just off straight. Once it warms up it's fine. I did some googling and that's when I found out about flushing the system (which made sense, since the fluid is thinner when warm, and on really cold mornings it was much worse, to a point where on a sub zero morning I had no power steering the first time I tried to turn the wheel).

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I would just put EBC back on the "I would not use their stuff" pile and move on.
    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
×
×
  • Create New...