Jump to content
SAU Community

Recommended Posts

Up for sale is my 89 R32 gtst type m.

The car is is excellent condition for its age and has just been resprayed about a year ago in the factory silver.

Reason for selling is I can no longer drive this car not being a on a full licence and don't have any points left to risk it. Otherwise I'd be keeping it as I love it to death.

Exterior

Looks wise its fairly standard, has the factory type m skirts, rear pods and I have recently sprayed and fitted a genuine Gtr front bar. Also have fitted a rear lip from viva garage which is fairly unique and in my opinion looks great. Currently rolling on r34 gt stock wheels all round with good rubber. The car sits approximately 1" lower than stock height on bilstein shocks, nice and stiff ride but not to stiff for daily driving (height is still very roadworthy).

Interior

The interior is nice and clean for an 89 model with no cracks or bubbles in the dash, only let down is a tiny rip on the drivers seat. Only interior mods are a boost gauge sneakily installed where the drivers air vent should be which I still have. Also the factory head unit has been replaced with an alpine head unit with an iphone/ipod cable neatly tucked away.

Engine mods

Most of the engine mods have been professionally fitted by the previous owner which include an r34 op6 turbo, nismo 555cc injectors, z32 afm, hks pod, blitz return flow intercooler, splitfire coilpacks, 3" turbo back exhaust currently with twin drift pipes at rear but I have 3" blitz rear muffler to make it quieter. The engine bay appears completely standard due to the return flow cooler and hks pod being mounted inside the shell of a standard airbox. Have had a hwy patrol officer look over and did not pick a single thing out.

The car runs fine and appears healthy but is in need a tune as it runs very rich and has alot more power potential.

estimating power figures at around 165rwkw at the moment.

Have recently done a little service which included and oil and filter change using motal 4100 and installed new ngk copper spark plugs. An oil change has been completed every 5000km's by me since I have owned the car.

bad points

-rear guards have had the lips rolled for bigger wheels

-slight weep of power steering fluid coming from hicas lines but doesn't drip has been like this since I have owned the car (will not be a roadworthy issue)

-small scratch on rear bumper (hardly noticable)

I'm not in a rush to sell so please don't attempt to low ball me, I'm after $8,000 which includes rego until december but no rwc at this stage.

Will put more photo's up this week or I can MMS photo's. 0408391831.

post-78664-0-22491400-1350481547_thumb.jpg

Edited by GTEES
Link to comment
https://www.sau.com.au/forums/topic/411789-vic-silver-r32-gtst/
Share on other sites

no RWC doesnt really need anything for it just maybe a drivers seat/ seat cover depending on the strictness of the mechanic and a rear muffler.

as far as i know zac. r32, you can only drive a turbo in vic if its got the factory manufacturing plates stamped as a low powered turbo (new cars only)

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...