Jump to content
SAU Community

Recommended Posts

  • Replies 46
  • Created
  • Last Reply

Top Posters In This Topic

No whips mate - this only became a problem when everyone decided to bring their mrs's...

I used to dj in a strip club as if going to this is an issue ;)

just stirring :) I thought it to be a night with the boys too...

:confused: being a send off for the 'sillyier people' in SAU who are going off and getting married :(

I didnt know about you DJ in a strip club!

Fark... just imagine... Oh... imagine :)

lol bar20, Spearmints Rhino is where its at ;)

Maybe in this day and age Daz but when i worked at bar20 it WAS the strip joint to be at - most of you the sphincter of the universes couldnt even :whackit: back when i was working there, 1994/5/6 :)

just stirring :( I thought it to be a night with the boys too...

:confused: being a send off for the 'sillyier people' in SAU who are going off and getting married :)

I didnt know about you DJ in a strip club!

Fark... just imagine... Oh... imagine ;)

I wasn't aware it had turned into some boys night out. I thought it was just a meal and tits????

Sorry for being a bit reclusive of late - been ill :D

Table booked under my name for 7.30pm

Show starts at 8.30 - then again at 9.30 and 10.30.

Meal costs about $15 for H U G E chicken schnitz + chips & salad.

Beer is $15 a jug - so, basic bar prices.

All very tame and good for a chuckle.

I have everyone's PMs and numbers sorted.

Geoff: sorry to hear about your back :P

Hope things improve - just think, Turismo 4 comes out tomorrow, so couch time can be spend learning the Nürburgring :)

Wow, what a great concept! :rofl:

Good to see those who actually turned up, thanks for organising it James - pity you couldn't stay though.

Special thanks for GTTR34 for his running commentary, mate you were loving it! Nice to meet you, hope to see you out on a few cruises in the future.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...