Jump to content
SAU Community

Fresh Build Blowby - Tuner Halted Tune

murrayis

By murrayis,
in Engines & Forced Induction

 Share

Recommended Posts

STATUS Grand Master

STATUS

Posted
Posted

Deadly serious. Ventilation like that can be caused by a number of different reasons. Anything that runs methanol is going to vent like that and a lot that run E85 will also. It doesn't necessarily indicate there is a problem.

70% of our tuning is e85 and we dont see that unless the engine is built to loose.
The Dan Grand Master

The Dan

Posted
Posted

70% of our tuning is e85 and we dont see that unless the engine is built to loose.

It's pretty hard to build a loose engine.

Poor catch can setup, poor ventilation in general and lack of a PCV valve can all contribute to breathing like that (visual smokiness).

The vapor coming from most breather filters is mainly steam. You can see the 'smoke' doesn't make it more than about 3 inches away from the filter before it dissipates.

wedge_r34gtr Mentor

wedge_r34gtr

Posted
Posted

70% of our tuning is e85 and we dont see that unless the engine is built to loose.

Paul's pretty anal with his clearences when he builds an engine....

Thanks guys, ill give the tuner a call this morning. I did think it was odd tp tale 2 hours that low on an engine that needs running in.

Was there any blow-by before you took it to the tuner?

AngryRB Grand Master

AngryRB

Posted
Posted

im pretty sure this tuner is the one that told me i needed a surge tank and 2* 044pumps to run ethanol and make 300kw, so i never used them. How many tuners would even put the car on the dyno until it was atleast idling? from what ive seen its too expensive to have a car sitting and not being actually tuned.

The Dan Grand Master

The Dan

Posted
Posted

Lol yes well I hold judgement and don't point fingers

You don't need to point fingers. Just tell him to run it in, not f**k around with the idle on a very fresh engine.

#1 way to kill a brand new engine = idle

NoFigJamHere Enthusiast

NoFigJamHere

Posted
Posted

When you say 5 year build how long was the engine sitting after build before you started it? It does look more like steam than smoke...take breather tank out n see if any water/condensation is visible..You need to get a bore scope and look inside before any hard running IMO....

The Bogan Grand Master

The Bogan

Posted
Posted

Im under the impression that you dont want to idle car at all on initial start up, you need to load it up as soon as possible to ensure you get good piston ring and bore seal, if you dont load it up you will not get the "sweet piston ring/bore/hone seal" that is needed and you will lose any hope of getting it later as you will have worn down the hone.

My boat was run in hard on the dyno then the next day it went to the drags, that was two years ago and its still going strong after a heap of track days/supersprints/drags.

A old mate of mine use to race his bike (2 stroker) and he also rebuilt his engine, he would swap out the piston and ring and hone the bore, he would then thrash the hell out of it straight away, it never had a issue.

Starting up cars/bikes/any motor because "its been sitting for a while" is the worst thing you can do to a motor, you can prep them for long stints of inactivity which will be 100 x better.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Duncan's V37.......race car?

      By MBS206 · Posted

      Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...