Jump to content
SAU Community

Recommended Posts

I've decided to build an overkill cooling system for my competition drift car as I have a pretty good system ATM yet still gets hot after hard laps on hot days.

So what I have planned is to put a large radiator inthe boot with sealed ducting in and out and two large fans pulling air out. I plan on laying the radiator almost flat on floor with a slight upward angle, air will be taken in from each rear 1/4 window which will be replaced with vents and ducted to a single Y joiner when then feeds the sealed duct to radiator.

The radiator I had in mind was an all alloy vx v8 radiator..they are huge along with two zirgo 3600cfm 16 sands behind it. I'll use a header tank in the boot and the engine vary to prevent air pockets.

can anyone see any potential issues?

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/414185-help-me-design-my-cooling-system/
Share on other sites

That will work. Minimum 300mm diam duct from each window. Where is the fuel cell? If underfloor, then you are going to have to make your exit vent in the rear panel between the taillights. There's low pressure behind the car there anyway, but perhaps less so when sideways.

Stand the radiator up as close to vertical as you can. You'll hate yourself trying to duct in and out of it if it is lying down at a low angle.

trust me ive tried a lot of things over the past few years and my current set up is as good as it gets. RB in an s chassis is always difficult to keep cool. it works fine for 90% of the time but low speed, high rpm, hot weather and continuous laps sees the temps sky rocket

If your laying it flat you'll need air bleeds on the top of the tanks. Header tank in the boot is not nessiary. It would be far better if you bought a PWR core and built you own end tanks that have a deliberate high point folded into them with a -6an air bleed fitting.

Lotus' have a frontal radiator with bleeds at the highest point. It makes life much easier if you use an evacuation filler when putting the coolant in.

Sucks the system into a vacuum and that same vacuum is used to draw coolant back into the system.

I've seen a couple of failed boot radiators that we've looked at fixing for customers but its usually easier to either redo the whole setup or go back to a proper air dam/frontal radiator setup.

The big things are air bleed points.

Cheap radiators.

The factory water pump won't be up to the job. It will circulate the water too slowly over that distance.

Hot spots in the system where air sits and steams.

The fan setups. The only thing you are doing essentially is removing the intercooler from in front of the radiator and increasing capacity. If you have a good quality cooler now then it probably isn't an air flow restriction.

If possible have you ducting coming from the underside the fans blowing up through the radiator and the shroud venting out from the topside.

Hot air rises so with low road speed your going to have radiating heat going upwards into the ducting channels only to be sucked back down through the hot radiator via the fans.

Yes the hot air should be sucked out but the heat will radiate upwards even when air flow is downwards.

Put an air temp sensor in the coupling you fabricate and monitor the heat inside there to determine if its working. Ideally ambient is best obviously

Your best source of info is actually to look at as many lotus exige setups as possible. They are done perfectly with air feeds from the bottom, coulings venting into negative pressure air flow, air bleeds at all critical points etx

Years ago that fella from Nispro had an I think S14 and he made a way for some of the post rad air to spin off the tips of the mechanical fan and ducted this air out through a hole in the bonnet .

I wouldn't think you're running the RBs std fan but it may be possible to do something with elec fans . I don't think the radiator cares where the hot air goes as long as it can go somewhere so more can be pulled through the core .

A .

Mate i just had a brain fart......

we have been drifting 500hp s1x Rb power cars for years here in WA and we have sorted the cooling problems... you neeeeeeeed to f**k off those thermo fans they just dont work... then use the old nidssan clutch fan and shroud, koyo rad and oil cooler (lots of guys put them in the corners but there gay and hit shit sooo i have a put mine inbetween the rad and FMIC and i cant get my oil temp over 90deg)...

and the biggest thing is fuel... we run e42 (E85 mixed 1/2 with BP98) Jewmix but E85 is even better.

oh and btw we had a guy do the rear radiator setup on a s13... it never worked just overheated constantly... he gave up and did what we where all doin

Edited by britz1

I have all that and it still won't work :( have clutch fan and new blades. quality radiator and everything else you mentioned and it works great but couldn't handle multiple laps of WA heat

hmmm well my car has a cold air unduction pipe and a 12L jun sump maby its the big sump that did the goods... took longer to heat up the oil.... oh and btw i was at adgp in my R33 and it was overheating during prac... but it runs BP98 and adgp was stupid hot this year and prity hard on the cars

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok i will get those 310mm. I found one but on a different site. This is the description on those...is it ok? Technical parameters: - Axle: front. - Disc type: ventilated. - Number of holes: 5. - Disc diameter: 310mm. - Total height with center: 54mm. - Thickness (new/min.): 30/28mm. - Designed for brake calipers manufacturer: Sumitomo.
    • You Gregged a whole racetrack!?
    • Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
×
×
  • Create New...