Jump to content
SAU Community

Nismo Clutches

Burto
 Share

Recommended Posts

51jay Mentor

51jay

Posted
Posted

I have the G Max twin plate in my R33 GTS25T I assume the actual feel of the clutch would be similar in the GTR though I think your's would be Pull type as against my push type.

It feels the same weight as standard but the take up is much more abrupt ie its either in or it's out. Forget about slipping the clutch as you engage.....until you've had a fair bit of practice there just isn't time... and it's not good to slip them either. look forward to a few embarrassing stalls "til you get used to it. Once you've got it sorted out though it's really good...I won't be going back to the normal type. They are supposed to be rattly in neutral and I think the OS Giken is, but mine is not. To sum up I think they are good for about 600hp and much better than going the heavy duty singe plate.

Link to comment
https://www.sau.com.au/forums/topic/41433-nismo-clutches/#findComment-850140
Share on other sites
Burto Collaborator

Burto

Posted
  • Author
Posted

Hey thanks for that, yeah i just got this email back from Nengun regarding their clutches:

"I will be adding all the ORC clutch range to the site soon. I highly recommend the ORC clutch over the Nismo one. Recently I saw the ORC drift car in action. I was absoulutely amazed at how much pressure the clutch was put under. On the nengun site the Black GTR34 has a twin plate ORC clutch in it. They are so strong and you dont get big quads everytime you have to push the clutch in. I stopped selling the OS brand because the flywheels warp. The light weight ORC Flywheel is 4.8 kg the Nismo one is 6.7 Standard is 9.7kgs.

I can sell the Twin plate ORC 709 /700Ps for 113,000 Yen + 23,500 yen for delivery

Total 136,500 Yen @AUS ANZ bank rate 77.12 is $1769.96 AUS

Regards

Brent"

Think i'll probably go with this one

Link to comment
https://www.sau.com.au/forums/topic/41433-nismo-clutches/#findComment-850867
Share on other sites
  • 2 weeks later...
meshmesh Mentor

meshmesh

Posted
Posted

I just installed my ORC Racing Ogura Twin Plate on my R33 GTR.. these clutches are a push type & the R33 box is a Pull type. So whilst I was installing the new box & the new clutch we needed the adapters to convert the box from pull to push cost $350 from Nissan for genuine parts. But damn, this cluch and flywheel make such a difference it's amazing. I believe these have the lightest flywheels at around 4kg's and you can tell too. The revving is now so linear and smooth, I actually feel boost comming on ~500rpm earlier. As far as embarrasing moments.. well hey I'm getting use to em, after 2days it's getting easier, the clutch pedal is not bad at all "I dunno what everyones on about how hard they are" in fact it's feels quite normal, maybe a tad harder than the standard pull singles. But definately feels tight and sure. These are also serviceable, so if the clutch dies, you can rebuild them for ~$1000. But the best thing I have to say is that sound... it's freaks everyone out, when you engaged the clutch the Rattle is awesome, cars next to you look and think "what the?" I love rolling all my mechanic mates who claim to be the be all and end all of performance tuners. I'd go past and see'em and tell them to listen to this sound and tell me what it is as I'm worried about it.. they all say "definately your thrust bearing is gone!!" ;) get's em all the time. Amatuers..

Link to comment
https://www.sau.com.au/forums/topic/41433-nismo-clutches/#findComment-870113
Share on other sites
tridentt150v Grand Master

tridentt150v

Posted
Posted

I agree with 51jay, th nismo Gmax is a 'hard to get used to' clutch, but it is tough with a good launch ability. Its either on or its off..............you can dump it hard and it just bogs down and goes.

But...................it makes my skyline bloody suicidal to drive in the rain. You dump the clutch, the wheels spin, the motor revs, you make more boost, the wheels spin harder, the motor revs harder, you make more boost etc etc etc You do the best launches on a wet day, and you don't even want to do it [f@#ckin' hard to explain to the cops who are right behind you].

Link to comment
https://www.sau.com.au/forums/topic/41433-nismo-clutches/#findComment-870197
Share on other sites
51jay Mentor

51jay

Posted
Posted

meshmesh..... Glad you like it....i won't say told you so !!. Never said they were hard..as in heavy.. just the opposit.. they feel like standard. But they are on or off!!! heehee!

The Nismo doesn't rattle like the others.

Tridentt150v.....hahaha!....you haven't mastered it yet....I have no problems taking off in the wet....even with cops behind me.

Link to comment
https://www.sau.com.au/forums/topic/41433-nismo-clutches/#findComment-870216
Share on other sites
ferni Grand Master

ferni

Posted
Posted

meshmesh ahhh ok, so we still don't know how the ORC goes...

1800 delivered from nengun... someone bite the bullet and get one :rofl:

This is what Brent (from nengun) said to me about the ORC

"700PS. I took a GTR34 for a drive today and felt very smooth. There is noise once you push the clutch in. "

as in can hold 700ps....

Link to comment
https://www.sau.com.au/forums/topic/41433-nismo-clutches/#findComment-871750
Share on other sites
meshmesh Mentor

meshmesh

Posted
Posted
meshmesh ahhh ok, so we still don't know how the ORC goes...

Hi ferni,

Not sure if I'm reading this wrong or not, but my clutch is an ORC Ogura Racing Twin Plate - Push Type Clutch.

Either way, I'm rapt with it. Especially the sound of the rattle. Just got to get use to the take off's, gets a bit embarrasing sometimes.

Link to comment
https://www.sau.com.au/forums/topic/41433-nismo-clutches/#findComment-871955
Share on other sites
ferni Grand Master

ferni

Posted
Posted

i may end up ordering one before that, mines at the end of its life...

Somone tried to tel me a twin plate wll get wrecked if you launch to many 6000rpm launches... i would think it would be stronger than a single heavy duty?

Link to comment
https://www.sau.com.au/forums/topic/41433-nismo-clutches/#findComment-871958
Share on other sites
meshmesh Mentor

meshmesh

Posted
Posted
Ahh ok...

and your happy with it?

It only rattles when clutch is pushed down to floor (ie disengaged) right?

I'd like to go for a ride in your car/hear/feel the clutch if your willing mesh

I Love it... Makes me feel like a man :)

Yes it only rattles when you push the clutch down, and obviously during gear changes. (whether this is called disengaged or not I dunno)

Just let me know when you wanna go for a ride.. the car should be at ICE either saturday or next week some time.

Link to comment
https://www.sau.com.au/forums/topic/41433-nismo-clutches/#findComment-872023
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The Bogan
      NC MX5

      By The Bogan · Posted

      After using a protractor for an actually accurate assessment of what is required,  and by NOT using my uncalibrated eyeball I worked out I need a 25° silicone bend from the TB ro the MAF, but, my choice was either a 30° or a 23° (23° is a weird spec), so I grabbed the 23° one from Raceworks I also grabbed 1mtr of 3" straight from Just Jap, I needed 350mm, but they only had 300mm, or 1mtr lengths....meh Also ordered a 1/2" hose bulkhead fitting from fleabay, this has a smoothish mushroom looking head (they are designed for below the water line of boats) that will fit inside the bend, the hose bit and threaded bit looks to long, but nothing that a hacksaw cannot fix if required, the hose will then just get jamed on the threaded bit up to the retaining nut Fingers crossed and the unsightly amount of hose clamps will be reduced down to 4 once all the parts arrive 
    • joshuaho96
      R34 25GT Engine Light 21

      By joshuaho96 · Posted

      Oil change does not trigger code 21. Code 21 is for coilpacks primary side connection. You can try to clear the code with a battery disconnect, hold down the brake pedal to drain capacitors through the brake lights with the ignition on for 10-15 seconds before you reconnect the battery. I have seen R35 coil conversion permanently cause this code with no ill effects so it might be the resistance it wants to see isn't quite right on one or more coilpacks. Could be inside the ECU, could be the harness, could be a coil. You can test it all if you want or just ignore until the car actually starts misfiring.
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I forgot you have a Nistune ECU. Use Nistune to do all the tests I mentioned instead of faffing with 30+ year old electrical connectors. You can read MAF volts off that too, there are reference values in the service manual to tell you roughly what it should be in different conditions.
    • GTSBoy
      R32 GTS (RB20DE) Injectors Replacement

      By GTSBoy · Posted

      No. I think it might be the AFM. Hence the use of the terms "swaptronics", which implies the use of swapping out electronics for the purpose of diagnosis. It's about the only way to prove that a small/niggling/whatever problem with an AFM or a CAS or similar is actually caused by that AFM/CAS/whatever. A known good item swapped in that still gives the same problem is likely to be caused somewhere else. They're all the same. Spraying AFMs with cleaner is an each way bet between cleaning it and f**king it.
    • codygrimm27
      Can you mount the ATTESA pump in other locations?

      By codygrimm27 · Posted

      Oh wow! This might actually work amazingly. Do you know the ratio of the diff? I was told the only thing you need to make sure of is if the front & rear diff ratios are the same. Ours is a 4.083 Thanks!
×
×
  • Create New...