Jump to content
SAU Community

Recommended Posts

I had a great morning, just looking at photos so I can remember what it looks like, in case I get into the wrong car at some time in the far distant future if I am called in to pick it up :)

I had a great morning, just looking at photos so I can remember what it looks like, in case I get into the wrong car at some time in the far distant future if I am called in to pick it up :)

I'm sure you have posted this, but what are you getting done? Sorry if I had missed the post.

  • 2 weeks later...

Replaced my rock hard rocker cover gaskets. Gotta love how much info is out on sau

I take it you did the half moons + goo?

59104439.jpg

I actually just received a new gasket for the RB Thirty.

Only needs one piece. :)

I take it you did the half moons + goo?

59104439.jpg

I actually just received a new gasket for the RB Thirty.

Only needs one piece. :)

I did indeed. Managed to find you in that thread also. Not surprising.. Always seem to find you in r33 tutorials! :laugh:

So... I got my first flat.

front left tyre shredded on the outside thread and airless. Walked to Servo > then got picked up and went to Robs for help because.. my jack didn't have no jack bar :( (lesson one) and so, Rob was very kind enough to help me change my tyre. I tried to help but I think I was getting in his way. Needless to say, Rob came to the damsel in distress :D So, thank you Rob.

Finally home..

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yeh I think i'll message an old contact i had for ages that manages his own tyre shop now.. n tell him what i want n work with him before ordering..  Got this 17x9 +30 Driftteks on 245/45/17 PSR Drag Radials on the rear.. They fit well - for your reference in future - Rear guards  have been lipped in & minimal to non flaring of the rear Gaurds.    
    • If only it were that easy! I also needed to remove seats, shocks, brake calipers, send my car through a fence, and use measuring and ended up guessing because I didn't remove seats, shocks and brake calipers. It can be hard sometimes Can be a little more complex than 'just measure' if you want to truly measure the entire wheel through all of it's suspension travel. But if you aren't going for every last mm then yeah, you can check the space you currently have and guesstimate.
    • If you own a car, and it has wheels on it, and you know the offset of those wheels, and you have a measuring device, you have everything you need to work out if other wheels will fit.
    • Will this fit? but they are staggered set - RAYS 57DR SEMI GLOSS BLACK 18x8.5 +37 | 18x9.5 +38 5-114.3 STAGGERED SET   or If no go could just get a set 4's wheels of 18x8.5 +37 5-114.3 - would i run 8.5's 235s up front n 245's at the back if I do?   Thanks.        
    • Put a clamp on your return line. I have a feeling it's sucking air, and introducing bubbles to your fuel. With a lot of fuel, less problematic. I'd honestly be redoing all the lines in the tank and clamps on everything.   Also, you've given two different answers to the same question: Asked if being followed by the police you could get down to use the whole tank, you said yes you could, so long as you keep off boost. However, you then followed this up that free revving, it would also cause the issues. I'm doubting free revving is enough to make any noticeable boost on what is likely a decent sized turbo.   So now I have to ask, can you actually drive it lightly and use all the fuel, or does it break up even free revving? Also, have you put a fuel pressure gauge on it? Can you hear the pump change noise at all when you're having this issue?
×
×
  • Create New...