Jump to content
SAU Community

Recommended Posts

Hey

I have recently bought a set of Dobi lowering springs (35mm) for my R33 GTS25 (2dr). I figured I would look for some second opinions on how to swap out the springs before I free wheel it. I have had a reasonable look but is there already a tutorial to swap out the springs? or can someone help me out with a basic run down? I would love a way that didn't involve removing the rear seats and parcel tray but I realise I can't always have it my way.

Cheers!!

Link to comment
https://www.sau.com.au/forums/topic/415891-lowering-springs/
Share on other sites

If your not mechanically minded then dont attempt it, you need a spring compressor to safely get the old ones off. It is pretty straight forwared though, jack car up, remove wheels, remove struts from the car, swap springs (and/or replace shocks), refit. If you dont have a spring compressor then maybe just get a workshop to do it.

Im pretty sure you dont need to remove the rear seats for the rear struts, I'll have to check mine but access is from the boot (I think).

33 gtst shocks have to be removed from inside the car, which means removing the seats and maybe the parcel tray, i installed coilovers in mine not too long ago, seats pretty easy to do just a lot of extra work...

Have no fear I am prepared with the necessary tools to swap springs and know of the power stored in them. I have swapped springs before but was more looking for tricks to know to make it easier for my car as I haven't done it on any nissan

Then get wheel alignment.......

But yeah, remove seats, remove or lift up parcel tray taking into account that if you have tint on the rear glass you may need to be very carefull to not scratch it with the stock speaker covers.

The struts tops are connected by 2 nuts, you will need to undo the front nuts on some electrical components that cover the strut tops first so you can move them out the way to get to the strut tops.

Then chock the front wheels and jack up the car, place in the safety stands, remove the wheels and then the lower bolt that holds the strut on, using a rubber mallet tap the strut off whilst holding onto the strut to stop it falling.

When replacing seat the top of the struts in the holes, place a jack under the lower part of the shock and slowly jack the shock onto the lower fixing point and tap it into place, do up bolts.

I do it this way by myself but if you have a mate handy you can leave one nut on the top of the strut so when you tap the lower point of it doesnt fall out and potentially damage your car, then hold the strut whilst your mate removes the top nut.

33 gtst shocks have to be removed from inside the car, which means removing the seats and maybe the parcel tray, i installed coilovers in mine not too long ago, seats pretty easy to do just a lot of extra work...

Atleast I know now for when I do my coilovers :)

Then get wheel alignment.......

But yeah, remove seats, remove or lift up parcel tray taking into account that if you have tint on the rear glass you may need to be very carefull to not scratch it with the stock speaker covers.

The struts tops are connected by 2 nuts, you will need to undo the front nuts on some electrical components that cover the strut tops first so you can move them out the way to get to the strut tops.

Then chock the front wheels and jack up the car, place in the safety stands, remove the wheels and then the lower bolt that holds the strut on, using a rubber mallet tap the strut off whilst holding onto the strut to stop it falling.

When replacing seat the top of the struts in the holes, place a jack under the lower part of the shock and slowly jack the shock onto the lower fixing point and tap it into place, do up bolts.

I do it this way by myself but if you have a mate handy you can leave one nut on the top of the strut so when you tap the lower point of it doesnt fall out and potentially damage your car, then hold the strut whilst your mate removes the top nut.

thats pretty much whats needed, i think one of the electrical things has something to do with the fuel gauge, went for a drive without reconnecting it and fuel gauge went to E

i actually broke a piece of my parcel shelf cause i didnt realise there are little clips you have to remove from inside the boot that hold it too the vent.

i found it easier to remove by removing the metal bracket/brace thing on either side of the shelf so i could bend each side down and lift the centre to make it easier...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Well, all the best with the new camry It was interesting to hear about the UK process, it is generally a lot more streamlined here with a shipping agent looking after all the import side (noting the exact final price can still be a surprise.....) and I've used a few different brokers on the japan (or US) side, and never had any trouble with any of them....luck of the draw I guess. You mentioned you didn't get the auction sheet (understandable since you bought it from a dealer, not auction), but I always try and get hold of that because they are pretty thorough. I've imported 2x R grade vehicles over the years and both were fine, repairs in Japan are pretty thorough compared to here in Oz.
    • BTW I measured the jack I have, it is 70mm at the saddle but you only have about 700 until it returns to 150mm high at the cylinder so it is good but no magic bullet.
    • My experience with Rising Sun Exports Before agreeing to the sale I tried to do as much research as I could (obviously), his Facebook reviews are 98% and he goes Live at least once or twice a week. I contacted 2 people in the UK who had used him for their imports, both had positive feedback. His explanation and talk through of the import process was thorough, answering any query no matter how stupid it was. It felt as soon as the money was sent, communication dropped off. I asked for shipping updates every 2 weeks or so, not wanting to pester him, he never had any updates. I wasn't informed the car had been dropped off at the port, I only found out by his Facebook story. I asked for the photos taken at the port, knowing he would need some for insurance purposes. I received a few 5 second clips and that's it. When asked again, he said his staff had them. Weeks later I asked again, he tells me he doesn't have any, but does have 50 photos from the original advert. I never received them. I eventually got the documents sent via WhatsApp after I mentioned the port was requesting them. I purchased a CarVX report, to find out the vehicle is a Grade R with recorded accident damage, first recorded in 2017 when it was first auctioned. He never told me the grade, then again I didn't ask. His response was "Grade R means nothing, it wasn't chassis damage". Still, I would have liked to have been informed about it. Jon prides himself on being open and honest when it comes to inspecting cars, it's his main job doing so at the auctions for customers. When the vehicle arrived in the UK I noticed a few little cosmetic issues. It's a 21 year old car so it wasn't going to be mint condition. The side skirts are cracked on each corner and the sealant is failing. The front grill on the bonnet/hood isn't secured very well, mounting studs are missing. Both minor things, but again, it would have been nice to be told. During a Facebook Live walk around video of the vehicle, he mentioned it has a front Whiteline anti roll bar/sway bar. While on the inspection ramp, I noticed the stock item has been installed. When first questioned, his response was "the ARB? Switched? Since when, it never had them". Since sending video and photo evidence I've not received a response. I'm probably being over critical of the overall condition of an old car, but all I wanted was honesty (which he claims to have). I'm aware I wasn't his only customer, he's busy doing XYZ but other reviews praise him for great communication with regular updates and photos, I felt I didn't receive the same treatment. 
    • I was able to get some underside photos while the car was on the ramp The suspension is all Altezza/IS200/IS300 so getting part's will hopefully be less of a headache
    • Welcome to my 2004 Toyota Mark ii IR-V Fortuna (series 2) With a 1JZ-GTE powerplant under the bonnet (hood) it'll give me plenty of scope for power upgrades. For those who aren't familiar with imports, the 1JZ-GTE is a 2.5L 6 cylinder VVTi engine with a single turbocharger. This has the factory R154 5 speed gearbox, along with a aftermarket 2 way LSD differential (brand unknown). Under the arches are a set of CST Zero 1 alloys, 18x9 +30 225/40 up front and 18x9.5 +15 265/35 on the rear. The car was quite low in Japan and there's evidence of the wheels catching the rolled arches/fenders. The tyre's aren't great so I'm in two minds whether to replace both or just the tyres and put up with the wider wheels on the rear. The car still uses stock brakes with the addition of some braided hoses. The exterior is stock with the exception of a BN Sports front bumper and a replacement Fortuna grill  Moving to the interior, the steering wheel has been replaced with a dished MOMO steering wheel (which will get swapped for my Momo Tuner for the time being) Defi Link Gauges are mounted above the climate controls and on the A pillar, the Oil Temp,Oil Pressure,Water Temp and Boost gauges should help with spirited and track driving  The stock seats have been replaced with some retrimmed Recaro bucket seats. Being a larger build these are a little snug, unfortunately the orange isn't for me so I'll look into replacing these down the line. Other modifications include a twin plate clutch, Blitz intercooler, Evolve alloy radiator, a stainless exhaust with decat, HKS EVC-S boost controller and coil overs
×
×
  • Create New...