Jump to content
SAU Community

Zoid Builds A 25\30

zoidbergmerc

By zoidbergmerc,
in Tasmania

 Share

Recommended Posts

brad 110 Collaborator

brad 110

Posted
Posted

I've taken .120 plus " off these heads and just remilled the oil feed relief, piston to valve like Ben suggested can be an issue as the VCt in the 20 deg advanced position will net you up to .180" lift at dtc on the inlet and by reducing the deck face the valve drop to head face will be reduced by close to same amount, this will vary on where the cams are dialled in. You will need to get Hollywood to straighten it first before you surface it unless you have a special set of cams with a bend in them to suit your as stated not perfectly straight cam tunnels and then just never rotate them!

What ever you need as listed above I have and no longer will be using off my shit box Datsun as heading down another path on the new engines let me know if I can help.

trustr32 Rising Star

trustr32

Posted
Posted

I was also eyeing off that GT3540 for sale in the other thread, will that fit in stock low mount position?

Why dont you see if you can borrow jacks for a test fit........... he's not using it lol

XRATED Veteran

XRATED

Posted
Posted

I doubt it mainly for the compressor housing.

Yeah, you'd have to space it out a fair bit.

I don't rate hifliws buy on a 3l it wouldn't be to bad. Depends what you are after. I've got exhaust manifold and turbo lines if you think you mite go that way.

Exh housing is too small for the 3lt, even the OP6 r34 housing... too much back pressure... ping ping ping

One of the best rb set ups I ever had together was the 25/30 in my old r32 gts-t.... 25/30, T6725g and 4.3 gears :-) so much torque! pretty much stand on it anywhere over 2k and it was wheel spin city!!

Maybe a td06 20g and get a t3 rear housing with v band dump to suit and whack an external gate on your std mani.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Dose Pipe Sutututu
      What should I do next to hold the head on

      By Dose Pipe Sutututu · Posted

      Possibly avoid using a Cometic one unless the deck/head surface are perfectly flat. I did have a look just then and forgiving gaskets such as Tomei or Nitto don't exist for the FJ20, however the Bar-Tek or Kameari ones look good and might do the trick.
    • GTSBoy
      boost source Size Garrett gt28 gen2

      By GTSBoy · Posted

      Because pipe threads for pipe things. M threads for bolt things. Throw some teflon sealant onto it and dust your hands off knowing you did the right thing, instead of going twice around the block to achieve a result using the wrong things. Of course, all of these solutions are ignoring the fact that the minimum thread pitch we're talking about here is 1.25mm, with the 1/4" in NPT or BPS being out around 1.4mm. You will need to know that the boss you're tapping has enough thickness for at least a few threads. That's one of the reasons that 1/8" is commonly used - because the pitch is <1mm. And why would you look to use 1/4" NPT in a BSP country anyway? Ugh.
    • Dose Pipe Sutututu
      boost source Size Garrett gt28 gen2

      By Dose Pipe Sutututu · Posted

      Just throwing around ideas, does it need to be in the compressor cover? Why not the hot side piping?
    • timmy94
      boost source Size Garrett gt28 gen2

      By timmy94 · Posted

      1/8NPT drill size = 8.7mm. Since the hole got messed up by me, it’s probably around 9mm.    So 1/4” NPT would be next step. A drill size of around 11mm would be preferred there which is not way of my M12 (drill 10.5mm and tap M12 threads) 
    • oHBoy.
      2001 R34DE

      By oHBoy. · Posted

      3 Kids are starting to hit that ages. I wanted to get them something special to learn on, put down the screens and have some fun. 4Door 2001 R34DE Black Pearl GV1 Jap Import, AU 2nd owner. Pre Work done. Suspension - Wheels Pedders SportsRyder Coilovers   Wheels TSG Spokey Boi 18'x9.5"+15 Body JASI Aero 4 door Type R Full Kit LED Conversion - Parker, Blinkers, & Reverse Exhaust Hurricane Headers 100 CPI high flow cat 2.5" Piping Cannon muffler Internal Bride low max stradia ii - front seats  Bride RO seat base and Rails (R/H) Cube short shifter LED Conversion - Interior   
×
×
  • Create New...