Jump to content
SAU Community

S A U - N S W Tech Night 21St Feb - Detailing


Recommended Posts

  • Replies 256
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Michael's got his wish!

P1050090_zps33dd49fe.jpg

P1050091_zpsab3634f0.jpg

P1050092_zps8b71cea2.jpg

P1050093_zps142449e7.jpg

P1050094_zpse96fbae3.jpg

P1050095_zpsf6b8e65e.jpg

Wow!

So now you've got the prettiest R31 in town Michael, who & what do you recommend?

Congrats Michael :)

You've never had so many people around your car have you?

Another quick update. Now that I've practiced the with the Carbon Di-Noc, attempted the grand plan item....

Mohawk for Godzilla! VERY pleased with the way it turned out.

Even used the trick with the kevlar thread to cut the edges and it worked a treat!

DiNoc3.JPG

DiNoc2.JPG

DiNoc1.JPG

Nice work Eric :thumbsup: that looks tops! Need better pics where we can see the carbon look in all its glory......... Or maybe its just my dodgy laptop screen thats just making it look black lol! But definately need some daylight pics :merli:

I finally managed to clay bar part of my car on Tuesday - did the Bonnet.

Took it out that night, got blinded by other cars headlights reflecting off the bonnet cos it was soooo shiny :D

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
    • It is the stock air box with the panel filter. Everything else is stock except the exhaust at this point, as I also went back to the cleaned 270cc injectors. I will check the RPM when the IACV is unplugged and report back.
    • As MBS suggested if this is happening when the engine is cold you're going to want to remove the intake air regulator and verify resistance + that the shutter is physically opening and closing. At -20C should be fully open, 20C half open, over 60C fully closed. At 20C should be 70-80 ohms. For AAC valve testing using a Consult cable see if you can raise and lower the idle by commanding more or less AAC duty cycle. Hopefully it's pretty linear as well, shouldn't be like 30% AAC valve is barely idling and 40% is 1500 rpm.
    • Bloody apprentices! 🙄
    • Not sure yet.  Was considering speedtek because it was rated to 800hp, but when I did some research about him I don't think I will go for that🤣 So maybe giken gear set, but I'm afraid it won't be strong enough🙄
×
×
  • Create New...