Jump to content
SAU Community

Recommended Posts

Bro press test.

Tried the pause on the chest. Found it better somehow.

130kg x 2 (warm up)

150kg x1

Dont have any more weights at home so 150kg is it. Probably not going to bench anymore. The home bench has broken during the racking. Besides not liking the movement.

thanks for the encouagement dan.

It wasn't a real session so I can't say the effort was solid, more like slack , I am not even slightly sore today ha ha...

Played basket ball with the kids yesterday as well , definately put lots more effort in there. Sore all over from that. Doing the jumps and layups I probably shouldn't cold ha ha... Was fun though.

ha ha... yes it's relatively heavy. That dude might do less than me but, I'm sure he's in good shape , 260kg dead is pretty good.

I am not really commited at the moment , mostly by comparision to how I used to work. I found some other nostalgia shots from the gym from back in the day. I would fall over after doing a few of these. I would also do my calf raises with this machine & weight.

I did 440kg on this session about 5 reps

ResizeofDCP_0508.jpg

Half way through the lift.

ResizeofRotationofDCP_0509.jpg[/url]

Edited by rev210

It was crazy ha ha...

480kg hack on the same day. This machine was a bit scary. The last safety above pretzel level , I would squat this deeper . failure was not an option..

I trained times when few people were around. I knicked most of the 20kg plates. Workout just loading them and unloading.

ResizeofRotationofDCP_0512.jpg

Edited by rev210
  • 1 month later...
  • 2 months later...

New years re-start & resolutions

* No more booze for 2014 Had several lifetimes worth, don't need it and would like to see the effect on my body composition.

* commitment to do something everyday.

Shoulder work today.

* Seated dumbell shoulder press . 45kg dumbells (90kg) 1 set of 8 .

* Lying dumbell face pulls. (lay down on a bench that is high enough or use an incline bench)

35kg (70kg) x 6

25kg (50kg) x 12

25kg (50kg) x 12

20kg (40kg) x 15

* Pushups

73

25

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Ok i will get those 310mm. I found one but on a different site. This is the description on those...is it ok? Technical parameters: - Axle: front. - Disc type: ventilated. - Number of holes: 5. - Disc diameter: 310mm. - Total height with center: 54mm. - Thickness (new/min.): 30/28mm. - Designed for brake calipers manufacturer: Sumitomo.
    • You Gregged a whole racetrack!?
    • Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
×
×
  • Create New...