Jump to content
SAU Community

R33 Gtr Engine Hoses

XGTRX

By XGTRX,
in Engines & Forced Induction

 Share

Recommended Posts

XGTRX Veteran

XGTRX

Posted
Posted

Wondering where people have sourced their engine hoses from. JustJap can't supply them at the moment, eBay has a few. Autobahn88 have theirs which i am leaning towards. Does any one know where to source genuine Nissan hoses from and are the silicone ones I have mentioned as good.

Thanks guys

Link to comment
https://www.sau.com.au/forums/topic/418478-r33-gtr-engine-hoses/
Share on other sites
GTScotT Grand Master

GTScotT

Posted
Posted

Not topic specific but I have recently built my motor and opted to go with the ASI hoses off ebay (similar to autobahn88)

they set me back next to nothing and the kit was both good quality and came with every hose that it should have. Fitment was perfect, I just needed to buy worm drive clamps as the silicon hoses are a little fatter.

The silicon will outlive the stock rubber hoses without the fact they are probably half perished from sitting on the shelf for nearly 2 decades.

http://www.ebay.com.au/itm/skyline-R33-R34-GTR-RB26DET-silicone-heater-hose-kit-/280887337908?pt=AU_Car_Parts_Accessories&hash=item416630a3b4&_uhb=1#ht_1240wt_1088

R31Nismoid Grand Master

R31Nismoid

Posted
Posted

Unless those ebay hoses have become better in the last 3-4 years, I'd be thinking twice... They tend to get spits and fail over time (2-3 years). I had a brand new Auto88 one spring a leak after only 2 months...

Nissan OEM - Lasted 20 years, will last another 20.

XGTRX Veteran

XGTRX

Posted
  • Author
Posted

Unless those ebay hoses have become better in the last 3-4 years, I'd be thinking twice... They tend to get spits and fail over time (2-3 years). I had a brand new Auto88 one spring a leak after only 2 months...

Nissan OEM - Lasted 20 years, will last another 20.

Where did you source these from? Tried nissan in victoria. I basically got told off for having an import and they said there is no way they can help me. I actually said that the r32 was aussie delivered and he told me no they werent..ha ha. I hung up

I would rather get OEM can you tell me where?

Hanaldo Grand Master

Hanaldo

Posted
Posted

Unless those ebay hoses have become better in the last 3-4 years, I'd be thinking twice... They tend to get spits and fail over time (2-3 years). I had a brand new Auto88 one spring a leak after only 2 months...

Nissan OEM - Lasted 20 years, will last another 20.

Have had Auto88 silicon radiator hoses on mine for 4 years now, no issues. Seen several track outings in that time as well. Read about these problems with them leaking a couple of months after I got them and was going to change back to rubber, but haven't had a need yet.

XGTRX Veteran

XGTRX

Posted
  • Author
Posted

Have had Auto88 silicon radiator hoses on mine for 4 years now, no issues. Seen several track outings in that time as well. Read about these problems with them leaking a couple of months after I got them and was going to change back to rubber, but haven't had a need yet.

I have done a bit of research on these hoses on other forums. People are pretty happy with these. any other experiences?

MrStabby Grand Master

MrStabby

Posted
Posted

Unless those ebay hoses have become better in the last 3-4 years, I'd be thinking twice... They tend to get spits and fail over time (2-3 years). I had a brand new Auto88 one spring a leak after only 2 months...

Yep ebay noname radiator hose lasted about 2 years for me. IIRC Beer Baron used to recommend the Samco brand if you're going for silicon, but i find silicon hoses are more leak prone than rubber. Rubber just seems to grip better and therefore provide a better seal. OEM only for me for coolant hoses now.

XGTRX Veteran

XGTRX

Posted
  • Author
Posted

Yep ebay noname radiator hose lasted about 2 years for me. IIRC Beer Baron used to recommend the Samco brand if you're going for silicon, but i find silicon hoses are more leak prone than rubber. Rubber just seems to grip better and therefore provide a better seal. OEM only for me for coolant hoses now.

I have read that people have been using zip ties to stop the hoses from creeping. Is it that much of an issue though. I have had similar issues with OEM hoses on other cars that I have owned. Is it really more of an issue with silicon hoses.

Hanaldo Grand Master

Hanaldo

Posted
Posted

I'm yet to have any personal experience with leaking silicon. I've got silicon radiator hoses, so do 3 of my mates, none with any leaking problems to date. That said, where there's smoke... I still keep a close eye on mine to make sure I don't get any leaks.

Roy Grand Master

Roy

Posted
Posted

Unless those ebay hoses have become better in the last 3-4 years, I'd be thinking twice... They tend to get spits and fail over time (2-3 years). I had a brand new Auto88 one spring a leak after only 2 months...

... recommend the Samco brand if you're going for silicon, but i find silicon hoses are more leak prone than rubber. ...

Provided the silicon hoses are reinforced, doesnt need to be steel but at least with some fibre core than they will out do and perform rubber hoses. Where they are weak and prone to problems is rough hands can damage them very easily and small cuts and nics seem to easily propogate into splits. So dont use screw drivers to lever clamps on and off. Make sure they dont rub against any sharp edges during install and the hose clamps have rounded sealing edges.

When they split early in their life its usually because they were damage by screwdrivers when being installed by Barney Rubble or someone like me :( Rubber is far more ductile it seems and takes abrasion a lot better

XGTRX Veteran

XGTRX

Posted
  • Author
Posted (edited)

Provided the silicon hoses are reinforced, doesnt need to be steel but at least with some fibre core than they will out do and perform rubber hoses. Where they are weak and prone to problems is rough hands can damage them very easily and small cuts and nics seem to easily propogate into splits. So dont use screw drivers to lever clamps on and off. Make sure they dont rub against any sharp edges during install and the hose clamps have rounded sealing edges.

When they split early in their life its usually because they were damage by screwdrivers when being installed by Barney Rubble or someone like me :( Rubber is far more ductile it seems and takes abrasion a lot better

Wow were you tapping my phone today. This is exactly what my engine builder said today.

He said that as long as the hoses are 3 ply reinforced or more there is no issue with splitting and they outlast and are more reliable than OEM on high performance engines, BUT care needs to be taken on installing them more than OEM. He said he has seen some failures with people forcing them at an angle and cutting through the inside of the hose.

Messaged the Autobahn88 hoses supplier and he said they are 4 ply, so my engine builder was happy going with them.

So am I with a full set including radiator hoses at $260.

Edited by XGTRX
GTR_JOEY Grand Master

GTR_JOEY

Posted
Posted

Oh god... 600-700 bucks for new hoses, I've got my engine out and I need to do the same thing

I know if I get genuine I can install and forget..

With silicon ill always have that question in the back of my mind..

What to do.. What to do

XGTRX Veteran

XGTRX

Posted
  • Author
Posted

Oh god... 600-700 bucks for new hoses, I've got my engine out and I need to do the same thing

I know if I get genuine I can install and forget..

With silicon ill always have that question in the back of my mind..

What to do.. What to do

Yeah I know the last thing you want to do is rip the engine out again for those 2 or 3 that you cant get to. Only saving grace for me is that my engine builder said he has never had a failure. so I suppose if I trust him with my whole engine rebuild, I should trust him with his opinion on hoses. Ordering Autobahn88 today. Very nervous about hitting that 'Buy Now' button. Might take some valium before I jump onto ebay.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • sonicii
      Could it really happen......

      By sonicii · Posted

      I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
    • Gareth87
      What should I do next to hold the head on

      By Gareth87 · Posted

      Thanks for the replies everyone. Definitely a coolant push. Oil catch can is empty and always has been. As the engine is out now I'll be having a good look over things. I do have some detonation on the piston tops from a trigger issue back about 5 years ago. I felt it and shut off then bought a new ecu and changed the trigger. Never been an issue since. It never hurt the power, its made almost 80hp more since that incident but I will pull the bearing caps to take a look. If the bearings are damaged I will do a bottom end refresh. Head is being re conditioned at the moment and the block will be cleaned and checked to ensure it's flat. I'll go with a kameari gasket and see how it ends up. The other thing I'm not super keen on is the cylinder colours. I suspect this is from the inlet manifold. The plan will be to put it back together, retune and then stick a plazmaman billet inlet on it and retune. I'm happy with the power, if it makes a little more, then great, but I would rather just make everything more efficient at this stage.
    • MBS206
      Could it really happen......

      By MBS206 · Posted

      Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
    • MBS206
      R34 25GT Engine Light 21

      By MBS206 · Posted

      Does it also misfire equally when revving?   Josh is very correct in what you should do. The coilpack harness wiring loom itself is a known problem due to its age and the number of heat cycles it has gone through. Throwing parts at a vehicle to diagnose the issue isn't a smart or good way to do it. Secondly, you may have a bad coil pack, you pop replacements in, they fix that issue, but messing with the harness breaks it, so the issue persists. So now you think "well it wasn't the coil packs" and have to continue chasing your tail, potentially swapping back in your shit coil packs and returning the good ones (yes, I've seen people do this because 'it wasn't the problem' and they want to save money). And suddenly, you've got two issues with the same symptoms...   Diagnose, don't use the spare parts shotgun.
    • V35_Paul
      Could it really happen......

      By V35_Paul · Posted

      Well the articals keep saying a Q50s (Skyline in Japan) with a new Manual gearbox. I like the talk about the new looks with the round tail lights. I hope they bring back the retro look like they did with the Z
×
×
  • Create New...