Jump to content
SAU Community

Recommended Posts

Wondering where people have sourced their engine hoses from. JustJap can't supply them at the moment, eBay has a few. Autobahn88 have theirs which i am leaning towards. Does any one know where to source genuine Nissan hoses from and are the silicone ones I have mentioned as good.

Thanks guys

Link to comment
https://www.sau.com.au/forums/topic/418478-r33-gtr-engine-hoses/
Share on other sites

Not topic specific but I have recently built my motor and opted to go with the ASI hoses off ebay (similar to autobahn88)

they set me back next to nothing and the kit was both good quality and came with every hose that it should have. Fitment was perfect, I just needed to buy worm drive clamps as the silicon hoses are a little fatter.

The silicon will outlive the stock rubber hoses without the fact they are probably half perished from sitting on the shelf for nearly 2 decades.

http://www.ebay.com.au/itm/skyline-R33-R34-GTR-RB26DET-silicone-heater-hose-kit-/280887337908?pt=AU_Car_Parts_Accessories&hash=item416630a3b4&_uhb=1#ht_1240wt_1088

Unless those ebay hoses have become better in the last 3-4 years, I'd be thinking twice... They tend to get spits and fail over time (2-3 years). I had a brand new Auto88 one spring a leak after only 2 months...

Nissan OEM - Lasted 20 years, will last another 20.

Unless those ebay hoses have become better in the last 3-4 years, I'd be thinking twice... They tend to get spits and fail over time (2-3 years). I had a brand new Auto88 one spring a leak after only 2 months...

Nissan OEM - Lasted 20 years, will last another 20.

Where did you source these from? Tried nissan in victoria. I basically got told off for having an import and they said there is no way they can help me. I actually said that the r32 was aussie delivered and he told me no they werent..ha ha. I hung up

I would rather get OEM can you tell me where?

Unless those ebay hoses have become better in the last 3-4 years, I'd be thinking twice... They tend to get spits and fail over time (2-3 years). I had a brand new Auto88 one spring a leak after only 2 months...

Nissan OEM - Lasted 20 years, will last another 20.

Have had Auto88 silicon radiator hoses on mine for 4 years now, no issues. Seen several track outings in that time as well. Read about these problems with them leaking a couple of months after I got them and was going to change back to rubber, but haven't had a need yet.

Have had Auto88 silicon radiator hoses on mine for 4 years now, no issues. Seen several track outings in that time as well. Read about these problems with them leaking a couple of months after I got them and was going to change back to rubber, but haven't had a need yet.

I have done a bit of research on these hoses on other forums. People are pretty happy with these. any other experiences?

Unless those ebay hoses have become better in the last 3-4 years, I'd be thinking twice... They tend to get spits and fail over time (2-3 years). I had a brand new Auto88 one spring a leak after only 2 months...

Yep ebay noname radiator hose lasted about 2 years for me. IIRC Beer Baron used to recommend the Samco brand if you're going for silicon, but i find silicon hoses are more leak prone than rubber. Rubber just seems to grip better and therefore provide a better seal. OEM only for me for coolant hoses now.

Yep ebay noname radiator hose lasted about 2 years for me. IIRC Beer Baron used to recommend the Samco brand if you're going for silicon, but i find silicon hoses are more leak prone than rubber. Rubber just seems to grip better and therefore provide a better seal. OEM only for me for coolant hoses now.

I have read that people have been using zip ties to stop the hoses from creeping. Is it that much of an issue though. I have had similar issues with OEM hoses on other cars that I have owned. Is it really more of an issue with silicon hoses.

I'm yet to have any personal experience with leaking silicon. I've got silicon radiator hoses, so do 3 of my mates, none with any leaking problems to date. That said, where there's smoke... I still keep a close eye on mine to make sure I don't get any leaks.

Unless those ebay hoses have become better in the last 3-4 years, I'd be thinking twice... They tend to get spits and fail over time (2-3 years). I had a brand new Auto88 one spring a leak after only 2 months...

... recommend the Samco brand if you're going for silicon, but i find silicon hoses are more leak prone than rubber. ...

Provided the silicon hoses are reinforced, doesnt need to be steel but at least with some fibre core than they will out do and perform rubber hoses. Where they are weak and prone to problems is rough hands can damage them very easily and small cuts and nics seem to easily propogate into splits. So dont use screw drivers to lever clamps on and off. Make sure they dont rub against any sharp edges during install and the hose clamps have rounded sealing edges.

When they split early in their life its usually because they were damage by screwdrivers when being installed by Barney Rubble or someone like me :( Rubber is far more ductile it seems and takes abrasion a lot better

Provided the silicon hoses are reinforced, doesnt need to be steel but at least with some fibre core than they will out do and perform rubber hoses. Where they are weak and prone to problems is rough hands can damage them very easily and small cuts and nics seem to easily propogate into splits. So dont use screw drivers to lever clamps on and off. Make sure they dont rub against any sharp edges during install and the hose clamps have rounded sealing edges.

When they split early in their life its usually because they were damage by screwdrivers when being installed by Barney Rubble or someone like me :( Rubber is far more ductile it seems and takes abrasion a lot better

Wow were you tapping my phone today. This is exactly what my engine builder said today.

He said that as long as the hoses are 3 ply reinforced or more there is no issue with splitting and they outlast and are more reliable than OEM on high performance engines, BUT care needs to be taken on installing them more than OEM. He said he has seen some failures with people forcing them at an angle and cutting through the inside of the hose.

Messaged the Autobahn88 hoses supplier and he said they are 4 ply, so my engine builder was happy going with them.

So am I with a full set including radiator hoses at $260.

Edited by XGTRX

Oh god... 600-700 bucks for new hoses, I've got my engine out and I need to do the same thing

I know if I get genuine I can install and forget..

With silicon ill always have that question in the back of my mind..

What to do.. What to do

Oh god... 600-700 bucks for new hoses, I've got my engine out and I need to do the same thing

I know if I get genuine I can install and forget..

With silicon ill always have that question in the back of my mind..

What to do.. What to do

Yeah I know the last thing you want to do is rip the engine out again for those 2 or 3 that you cant get to. Only saving grace for me is that my engine builder said he has never had a failure. so I suppose if I trust him with my whole engine rebuild, I should trust him with his opinion on hoses. Ordering Autobahn88 today. Very nervous about hitting that 'Buy Now' button. Might take some valium before I jump onto ebay.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So stock ECU does not like anything above 10 psi?  That Nistune one is just for "try" if it will be any different, I know it need to be tune for that. I know but YOU may know about these problem but i/we dont. They few little Skylines here let alone people who know anything about tham so that is why iam asking here  
    • So now we have a radiator with no attachments whatsoever. It lifts up with a particularly tight spot between the drivers side air box mount and the lower radiator outlet, but if you've got this far you will sort that too. This is the lower mounts with the rad out so you can see where the rubber bushes go, it is a straight shot upwards Done! Assembly is the reverse of disassembly, with blood less likely to be shed.
    • Right, onto the second last trick. The Air Con condenser is mounted to the front of the radiator and stays in the car when the radiator is removed. There are 2x 10mm headed self tappers holding the top of the condenser to the radiator, remove those The bottom of the condenser is attached to the radiator with clips. You need to lift the condenser out of those clips and clear (up, then forward). f**ked if  could work out how to do that last bit with the front bumper on. I hope you can, and you share the trick.  Bumper removal probably deserves its own thread one day once I've recovered the will to live, but basically you need to remove the wheels, front inner guard liners (clips and 10mm headed bolts), the self tapper between the guard and the bumper at the rearmost point of the bumper (same as an R32 that bit), any remaining clips at the top/front of the grill, an absolute bastard design with a plate that holds the top of the bumper above the headlight each side (only 1 bolt which is tricky to get to, but the plate catches 2 places on the bumper and must be removed....carefully!) and push clips between the bumper and guard under the headlight. If you've done all that you will be faced with wiring for the fog lights on both sides and in ADM Q50 RS at least, 4 nasty tight plugs on the driver's side for the ADAS stuff. So, the clips at the bottom look like this on drivers side (looking from the front) And on the passenger side (also from the front), you can see this one is already out Clearance on both of these are super tight; the condenser needs to move up but the upper rad support mount prevents that, and the radiator can't move down far because it is (rubber) mounted. Once you achieve the impossible and drop the condenser off those mounts so it does not stop the rad moving, you are good to go
    • OK, next the shroud needs to come off and there are a couple of tricks. Firstly, there is a loom from near the passenger side headlight to the fans, coolant temp sensor etc and there is no plug to undo.  In my case I was OK to leave the shroud on top of the engine so I just undid the passenger side fan plug and about 10 of the clips which gave enough free wire to put it aside. The fan plugs were super tight, the trick I used was a small falt screwdriver to push down on the release tab, then a larger flat screwdriver to lever the plug out of the fan unit....be careful with how much force you apply! If you need to remove the shroud altogether for some reason you will have to deal with all the plugs (tight) and clips (brittle)....good luck. I removed all of the clips and replaced them with cable ties that I will just cut next time. Also, in the Red Sport / 400R at least, the intake heat exchanger reservoir hose is bolted to the shroud in 2 places with 10mm headed bolts; so remove them (the hose stays in the car; no need to undo it at the t fittings down at the radiator lower mount. Once you've dealt with the HX hose and the wiring loom, there are 3x 10mm headed self tappers holding the top of the shroud to the radiator; remove those.   The shroud then lifts out of the bottom mounts where it sits on the radiator, up and onto the engine out of the way. Simples
    • Ok, disregard my “rate them” comment, sorry for my unrealistic input
×
×
  • Create New...