Jump to content
SAU Community

Recommended Posts

So today i parked my car in the usual spot at work and did not move it for 9ish hours. I got in my car this afternoon to move it around the back of my work (as i'm storing it in the workshop because we're getting a f*ck load of rain/flood) and all of a sudden my revs drop from 2k to 0 and the car stalls. I naturally thought "What the f*ck?" then i started the car again, drive 10 metres then it cuts again. So now i'm starting to get worried.. started the car again and drove another 15m into the workshop then turned it off.

When i first lost revs i also got a few lights come up from what i remember it was battery and a few others. Popped the bonnet and had a look around checked the belts to see if they were very loose but they were tight and everything else seemed ok. I am really not sure what's happened, we have got a hell of a lot of rain up here in the last 48 hours i'm just wondering if my car has just died because it's been driven 20m in the last 2 days and hasn't warmed up at all since it's been left in the cold the whole time.

Any feedback would be good, hopefully i get in it tomorrow and it starts fine and i have no problems.

Link to comment
https://www.sau.com.au/forums/topic/418485-strange-experience-today/
Share on other sites

id guess its fuel or air related - something to do with the fuel pump or your intake.

just some ideas:

that stalling sounds very similar to when the fuel pump has no power, it doesnt pressurise the injection manifold, the manifold has enough fuel in there to start and run for a while then eventually dies. but then you shouldnt be able to restart the car afterwards.... which would indicate a possible faulty pump. (or no fuel in the tank)

Or if your MAF sensor plug was disconnected, similar result...

or an inlet leak of some kind could do that.

i'd check the CAI hasnt popped off somewhere between the MAF and the plenum, or maybe a hose connected to the plenum (EGR or crankcase breather)

worst comes to worst, plugging a scantool up should give you a better idea

it will be a crank angle sensor or one of the cam shaft sensors. get it to a diag tool and it will give you the code, then look it up on google it will tell you what sensor it is. happened to me and it was my camshaft left hand side. about a $300 fix all up

I had a similar issue to this a while back, went to take off from the lights a few times then BAM! Felt like the engine died, hazards went on... fail. I checked a few things similar to what was suggested, disconnected the battery, reconnected, seemed to work fine after that :S Not sure if it was 100% the same however.

I would look at the cam/crank sensor too.. a failed fuel pump or air leak will generally cause it to stumble and run horrible for a bit before it stalls.. Check the codes.. it should have stored something if it is a failed Crank/Cam sensor.

Ok so i checked the MAF and intake this morning when i got to work and it all seems tight, started it up and let it get warm. Drove it around same as i did yesterday and had no problems at all. So i guess it's all sweet, if i have the problem again i'll get a scan tool on it.

Thanks for the advice

I think the engine light came on, to be honest i just thought to myself ahhh shit then tried starting the car again i didn't take note of exactly which lights came on. Yes Tony i used the clutch appropriately haha, thanks mate it's fine up here now haven't had rain since yesterday afternoon it's nice and sunny now with a bit of cloud so i reckon it's gone further south. My boss was blocked in this morning had trees down over his driveway and smashed windows from the wind.. got pretty crazy out where he is.

I have a set of Camshaft sensors, ordered from the US last may but took an age to get here and needed the car working to hit the snow fields so took it to Nissan Artarmon and had them replace the fault sensor at nissan pricing.

think they cost around $70 each ill have to double check, but cheaper than from Nissan direct

Cheers

James

Hey James, for future reference which shop did you buy the cam sensors from? Did a bit of a search on the net and couldn't seem to find anywhere. By the way, i drove the car home after work and had no problems at all. Really is a mystery as to what happened, i still think somehow it's because of the cold over the last 3 days.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Impossible to remove the housing while turbo is installed on the manifold on the engine. So I have to do it anyways. I plugged it so there will not be any debris in there. Will vacuum aswell 
    • would a r34 gtr hood line up with gt/gtt stock fenders? after latch, front bumper and hinges are swapped for gtr ones? or would the fenders be too low or high in relation to the hood surface? ( I believe seeing somewhere that gtr front fenders use some type of riser for the sides, but do not know how that relates to stock gt/gtt fenders.)    
    • You just need to remove the compressor housing, not the entire turbo. I would not be drilling and tapping anything with the housing still on anyways. 
    • So, I put my boat on a boat. First of all, I'm going to come out and say it. Why is Tasmania not considered a holy goal, an apex that all road-legal modified cars go to, to experience? This place is an absolute wonderland of titanic proportions. If people are already getting club runs for once in a lifetime 30 person cruises to Tassy then I've never seemed to see it. It is like someone replaced the entire place with an idyllic wonderland for cars, and all of the people living there with paid actors who are kind, humble, and friendly. Dear god. After doing a lap of almost all of the place I've found that it's a great way to find out all of the little things that the car isn't doing quite right and a great way to figure it all out. All in all, I drove for 4 hours a day for a week and nothing broke. I didn't even need to open the engine bay. This is by all means a great success, but it has left me with a list of things to potentially address. I also now have a 3D printed wheel fitment tool which annoyingly hasn't got any threads in it to actually assemble it. I might be able to tape it together to check the sizing I actually want to use, but it'll likely involving pulling the shocks out to properly measure travel at least at the front, and probably raise the car while I'm at it, at least in the rear. I scraped on quite a few things and I'm not sure how else to go about it. I was taking anything with a bump at what felt like 89 degree angles. And address those 10 other tasks. And wash the car. God damn it is dirty. And somehow, the weather was perfect the entire time - And because I was on the top of Mt Wellington it turns out it was very much about to freeze up there. I did something I typically never do and took some photos up there in what must have been -10 and the foggy felt like suspended ice, rather than mere fog. If you own a car in Australia, you owe it to yourself to do it.
    • Damn that was hilarious, and a bit embarrassing for skylines in general 😂 vintage car life ey. That R33 really stomped. Pretty entertaining stuff
×
×
  • Create New...