Jump to content
SAU Community

Speed Off The Streets - March 9 - Wakefield Park - $150 Entry


Recommended Posts

The Rotary Enthusists of NSW (RENEW) have some track days booked this year and would like to invite members of this forum to enter. The first event is at Wakefield Park on the 9th of March.

Our days are run as a track day, not a supersprint, and focus on maximum track time and therefore the maximum opportunity to improve driving skills. All our trackdays have timing included in the entry fee and results go on Natsoft. We limit the entries to four speed groups with a maximum of 12 cars per group. This is not a free for all with oversubscribed entries and that means more clean laps and making the most of your track time. We always have a broad variety of cars at our events, not just rotaries, and the mood of the days are always relaxed and friendly.

The speed groups are carefully monitored and regularly re-assessed throughout the day to keep it safe and enjoyable. There are a number of untimmed sessions in the day so drivers can take an instructor along with them to fine tune their driving. One of our members found a five second improvement after just one instructor session - and his case is not unusual.

We always welcome people with interesting cars and the right attitude including first timers. We will have the link to the entry form up in a few days. Hope you can make it.

**Title changed as no longer a Renew Track day - See further down for info from gregor** -

Edited by NISMO

Sorry for the late response, had some issues getting the form up on our site. I've attached it here for now.

Entry cost is $250 for members, $290 for non members. Fire extinguisher is mandatory for all entrants.

All welcome, even the wasteland's most prolific trolls :cheers:

WP_entry_form_9th_March_2013.pdf

WOW my 32 track car might just be ready as most of the stuff is getting fitted the week of the 25th of FEB. Cage ect. If shes a goer i may enter.

  • 2 weeks later...

Due to an underwhelming number of entries this event will now be run as a speed off the streets day by Wakefield Park. Entry cost is $150, rock up and pay on the day. Fire extinguishers are no longer mandatory as per other speed off the street events.

Edited by gregor


  • Similar Content

  • Latest Posts

    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
×
×
  • Create New...