Jump to content
SAU Community

Recommended Posts

Home already? Sounds like you really are doing great, considering the surgery that you have had. Healing around the head is a slow process, but if you are now reading this at home, well done mate!

And thanks to the Big Fella upstairs!

Great to see you in good spirits, and wanting to do stuff, even though you probably shouldn't! lol.

I am so happy for you, it brought a tear to my eye.

I ported mine back in November. Started with a Dremel and immediately saw that wasn't going to work.

Use a air diegrinder. If you don't have a carbide cutter I got mine in the router section at bunnings. Was like $25 or something like that. I was surprised that it chewed little iron shavings out of the cast manifold pretty well. I just used the gasket to port match.

Took me about an hour or hour + 1/2 to do two manifolds. Oh, and wear a face shield if you have it. Lots of little iron filings fly everywhere.

Help me Rhonda ! They have been great although he tried to kill me today pulling the 3/4" tape covering the scar off !! f**k me that's intense pain cause there is skin and hair and no easy way just this will hurt rip staples werent too bad though

My niece had one of these things taken out in december ,

took 9 hours in surgery.She was also 5 months pregnant as well,it was not malignent.

She is now 7 months gone but is not out of the woods yet,she got golden staph inside her skull,

proving hard to get rid of.

So glad you are doing so well look after your self. :)

Apparently the tumor was just penetrating the skull so they have to de calcify the piece if skull which will take another week he is very happy though so should be ok, that sucks for your niece best of luck with it. Sounds like we should have a tumor club not funny I know but funny how many ppl share similar experiences

I hope your story ends well

Unfortunately my wife's didn't, but she had a grade 4 glioblastoma multiforme, which is as aggressive as they get

That's really sad to hear mate.

I can't even imagine that....never want to either

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
    • I checked spark on all cylinders and they all visually have spark with the plug pulled and grounded, but plug 1 is the only one that fouled. This was a running swap that blew up and was rebuilt by a machine shop, put a new wiring specialties harness and did all gaskets, studs, and bolts while it was out.  compression is 135-150 across all cylinders. Aside from that from my understanding with the z32 ecu and maf the car should start regardless. The wiring for TPS and the dual 02 sensor/ dual knock sensor stuff shouldn’t actually stop the car from starting or even running well, (just slightly rich)  they just give fault codes. Car supposedly is supposed to start as long as you have z32 afm and ecu with the nistune base map and that’s info coming from a well known and trusted tuner who does a lot with SR/RB (Rsenthalpy). After more trouble shooting today where I’m at right now is that the cas is sending signal to the injectors they click while spinning the rotor, Fuel pressure is now set at 43psi, all cylinders have good compression and all of the plugs looked great (just wet with fuel) except for cylinder 1 which was very black (cylinder 1 has 150psi compression). all of the coils generate spark if pulled out and grounded out on the head. On the fuel pump car just pops into the exhaust. On starting fluid car will fire off. Hard to tell if all cylinders are firing off but definitley a couple. sounds like all of them but it’s only for 3-5 seconds hard to tell. 
×
×
  • Create New...