Jump to content
SAU Community

Recommended Posts

Got a lot of play in it.

When coming on and off throttle it has a lot of slap to it.

Pulled it out and shane took it to the diff place today, they said it needs new bearings

So they think bearings and adjustment? How much they quote to do it?

Link to comment
https://www.sau.com.au/forums/topic/419815-wtb-r33-diff/#findComment-6748118
Share on other sites

So they think bearings and adjustment? How much they quote to do it?

He didn't get a quote from them.

But someone at his work said $150 labour + a case of jimmy (I supply the bearings)

But honestly it wouldnt be that hard to put the bearings in myself.

Or at that kinda cost I can pick up a second handy

Link to comment
https://www.sau.com.au/forums/topic/419815-wtb-r33-diff/#findComment-6748121
Share on other sites

You can do it yourself if you read up and learn man, the bearings arent THAT bad to do, i am too lazy to do my own lol

You just need to make sure you read up on the adjustment as too tight and itll be noisy until you fark it, too loose and itll be back to square one!

Link to comment
https://www.sau.com.au/forums/topic/419815-wtb-r33-diff/#findComment-6748134
Share on other sites

R33 LSD Diff for sale.

Locks up nice in a straight line but tends to single peg a bit on roundabouts.

Would be perfect for a re shim.

$100 pick up QBN

PLS PM or 0413 88 44 oh 8

James

My Fellow R33 4Door owner has / had a Diff For Sale. ^^^ Check it. :thumbsup:

Link to comment
https://www.sau.com.au/forums/topic/419815-wtb-r33-diff/#findComment-6748340
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The cross sectional area of a circular hole scales with the square of diameter. So a 2mm diameter hole is 4x the area of a 1mm hole. Not double. The 1.7mm hole is nearly 3x the area of a 1mm hole. You do not need restrictors at both ends of the oil supply line. If you have new, additional restrictors at the turbo end, that you did not have before, then you do not need a restrictor at the inlet end.
    • Hi all. Been a while but things are moving along. I just have something that I am wondering about. Since I will use OEM turbo oil pumbing, I got myself a new bolt, the one that goes into the engine block oil feed. As I recall (and see visually) this bolt comes restricted with I think a 1.7mm hole? Not quite sure but it was something around that size. The turbos have 1mm restrictor bolts installed, as necessary due to ball bearings and my higher oil pressures. Can I now just use that OEM bolt with the 1.7mm hole in for the engine block or will this actually be too much oil flow restriction and I have to drill it out first? In my head it would make sense for the bolt to be at least 2mm wide as both turbos take "1mm of oil flow". Do let me know if my logic is flawed here, I just want to make sure I don't kill my turbo bearings with too little oil. Don't know if I can trust the saying I read somewhere that ball bearing turbos essentially only need an oil mist
    • There are several aftermarket options available, from not-too-painful moneyhttps://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35 and  https://justjap.com/products/crank-motorsport-billet-rear-axles-fits-nissan-skyline-r33-gts-t-r34-gt-t?srsltid=AfmBOorQk4xkGUa98kO7v2ePLUiNt-HRrM2AwWNw9mbSIVE1ujBVwY__, all the way up to The Driveshaft Shop https://driveshaftshop.com/skyline-cv-axles/
    • Yeah based on old XRC5964S specs, it looks to be roughly GTX3576R sized? But this 5964S compressor will flow 90lb airflow somewhat similar to the compressors in both the GTX3584RS or G35-1050.. I fully expected the 0.64 rear A/R to choke up top - seems way too small from typical convention - but these are seemingly beneficial over the prior 0.82 results.. Be interesting to see if he comments on the EFR question in that thread - he mentioned in a prior video that BW EFR's were the "cats pajamas 10 years ago", but by the sounds of things all his kits have been using Xona for quite a while now.
    • Yeah it’s still got the oem manual gearbox and clutch, only kinda mods are a blow off valve, coil overs, and a aftermarket intercooler. Also had it for about 2 months now with a lovely midnight purple paint on it.
×
×
  • Create New...