Jump to content
SAU Community

Recommended Posts

Hey guy.

Was looking at my recently purchased C34 yesterday and noticed what I thought was a funny setup with the fuel hoses. In the engine bay it goes from hard line to soft line, then to the Tomi fuel reg then to the fuel rail. Then what I assumed was the return line to the tank, coming out of near the firewall, was the fuel filter. Do the rb25det neos run like this or has an idiot assembled it wrong?

My guess is the latter as it doesn't appear to make sense otherwise.

Cheers,

- Lance

Link to comment
https://www.sau.com.au/forums/topic/420119-c34-fuel-setup/
Share on other sites

On the S1 ( I still have stock set-up) the fuel system goes like this:

The hard pipe goes to a fuel filter mounted in the engine bay near the RH strut tower and a rubber hose goes to the back (firewall) end of the fuel rail. There is a fuel regulator (still using the stocker) at the front end of the fuel rail and a rubber hose goes from there to a damper mounted just behind the filter and the return goes from there to the tank.

Link to comment
https://www.sau.com.au/forums/topic/420119-c34-fuel-setup/#findComment-6758207
Share on other sites

Okay thanks for that.

Mine isn't standard so it's hard for me to tell how it's meant to be. Does the fuel go in from the front or rear of the fuel rail? At the moment mine goes from the hard line, to a rubber line into the filter, then through the Tomei fuel pressure regulator (mounted on the drivers side strut tower) via rubber line into the front of the fuel rail. Then a rubber pipe comes off the back of the rail to the hard return line.

- Lance

Link to comment
https://www.sau.com.au/forums/topic/420119-c34-fuel-setup/#findComment-6758386
Share on other sites

Okay thanks for that.

Mine isn't standard so it's hard for me to tell how it's meant to be. Does the fuel go in from the front or rear of the fuel rail? At the moment mine goes from the hard line, to a rubber line into the filter, then through the Tomei fuel pressure regulator (mounted on the drivers side strut tower) via rubber line into the front of the fuel rail. Then a rubber pipe comes off the back of the rail to the hard return line.

- Lance

No the regulator is at the end of the rail thus pressurising the rail. Its possible yours is plumbed wrongly. Have you pulled off a hose and turned on the pump to confirm where the fuel is coming from? Maybe you are returning fuel via the filter! Does your car run properly??!

Link to comment
https://www.sau.com.au/forums/topic/420119-c34-fuel-setup/#findComment-6759164
Share on other sites

I've re done it all last night. The car was surprisingly running well even with the fuel filter on the return line, and backwards. Now I've got it going from the hard line, to rubber through the filter, into the back of the fuel rail. From the fuel rail to rubber to the reg, then rubber down to the hard return. Sound alright?

Cheers,

- Lance

Link to comment
https://www.sau.com.au/forums/topic/420119-c34-fuel-setup/#findComment-6759178
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
    • I forgot about my shiny new plates!
    • Well, apparently they do fit, however this wont be a problem if not because the car will be stationary while i do the suspension work. I was just going to use the 16's to roll the old girl around if I needed to. I just need to get the E90 back on the road first. Yes! I'm a believer! 🙌 So, I contacted them because the site kinda sucks and I was really confused about what I'd need. They put together a package for me and because I was spraying all the seat surfaces and not doing spot fixes I decided not to send them a headrest to colour match, I just used their colour on file (and it was spot on).  I got some heavy duty cleaner, 1L of colour, a small bottle of dye hardener and a small bottle of the dye top coat. I also got a spray gun as I needed a larger nozzle than the gun I had and it was only $40 extra. From memory the total was ~$450 ish. Its not cheap but the result is awesome. They did add repair bits and pieces to the quote originally and the cost came down significantly when I said I didn't need any repair products. I did it over a weekend. The only issues I had were my own; I forgot to mix the hardener into the dye two coats but I had enough dye for 2 more coats with the hardener. I also just used up all the dye because why not and i rushed the last coat which gave me some runs. Thankfully the runs are under the headrests. The gun pattern wasn't great, very round and would have been better if it was a line. It made it a little tricky to get consistent coverage and I think having done the extra coats probably helped conceal any coverage issues. I contacted them again a few months later so I could get our X5 done (who the f**k thought white leather was a good idea for a family car?!) and they said they had some training to do in Sydney and I could get a reduced rate on the leather fix in the X5 if I let them demo their product on our car. So I agreed. When I took Bec in the E39 to pick it up, I showed them the job I'd done in my car and they were all (students included) really impressed. Note that they said the runs I created could be fixed easily at the time with a brush or an air compressor gun. So, now with the two cars done I can absolutely recommend Colourlock.  I'll take pics of both interiors and create a new thread.
×
×
  • Create New...