Jump to content
SAU Community

Recommended Posts

first i've missed in about 6 months.

got a last min call to Hong Kong for work.

Wish my work would last minute call me to Hong Kong... ...Instead I get called to wash old men that have pooped themselves... >_<

:rofl:

I would say Hong Kong has plenty of computer geeks...

but none as special as me...

the computer system i'm playing with today has a Nuclear reactor attached to it!

guess that why they don;t want some-one connecting from Overseas to it..

but none as special as me...

the computer system i'm playing with today has a Nuclear reactor attached to it!

guess that why they don;t want some-one connecting from Overseas to it..

Damn! Serious business!

:rofl:

but none as special as me...

the computer system i'm playing with today has a Nuclear reactor attached to it!

guess that why they don;t want some-one connecting from Overseas to it..

I thought that would be an offline, secured network kind of thing? Why is it accessibly remotely?

Wondered the same thing about how people hacked into Crown's security cameras recently in that 30 million dollar scam.

tell me about it I,

lucky I played simcity lots years ago to know how to deal with one.

As long as the robot monster doesn't show up (or a tidal wave, I hear reactors don't like them) you should be sweet.

Wondered the same thing about how people hacked into Crown's security cameras recently in that 30 million dollar scam.

Probably using Linksys Wireless IP Cameras with the standard admin/admin login ;)

I thought that would be an offline, secured network kind of thing? Why is it accessibly remotely?

Wondered the same thing about how people hacked into Crown's security cameras recently in that 30 million dollar scam.

it's not online thus why I had to fly to HK to do the work, where as with most corp customers I can remote in and work from AU.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...