Jump to content
SAU Community

Head Gasket Choice

e30h26

By e30h26,
in Engines & Forced Induction

 Share

Recommended Posts

e30h26 Contributor

e30h26

Posted
Posted

Hey folks,

I've tried using an online compression ratio calculator to work out what headgasket thickness I should be going for but its not making any sense (probably my stupidity). The basic spec of the build is as follows:

R32 Rb25DE with HKS2535/GTX3071 hybrid

GTR crank, rods and pistons

Nothing skimmed

I'm aiming for a massively responsive 450 on pump fuel. Can anyone advise what gasket thickness to go for or at least what CR I'd get with this set up on a standard head gasket so I can work it out?

Cheers.

Link to comment
https://www.sau.com.au/forums/topic/421199-head-gasket-choice/
Share on other sites
SilverECR33 Veteran

SilverECR33

Posted
Posted (edited)

CR wont change much, but your Quench will. id use a stocker. or a similar sized mls, the stocker is 0.9 i think. Ive got a multilayer rb25 metal MLS gasket for sale (used once), has it doesnt work on my 30/25 build. for $50 if you need it. it measures at 1.1 i think. pm me if ur interested.

Edited by SilverECR33
89CAL Grand Master

89CAL

Posted
Posted

If you have an MLS gasket the block and head need a near perfect flat finish. If you haven't touched the mating.surfaces then it might not seal. If you have a normal gasket you might get away with it but I'd still like to finish the block surface if it was me

e30h26 Contributor

e30h26

Posted
  • Author
Posted

The block and head have been checked and are flat from all angles that we tried. All the standard gasket material has been cleaned off so I'm happy it will seal. Im still trying to work out what CR i will end up with from either a 1.1mm or 1.5mm gasket though.

Can anyone tell me what the piston dome volume for a standard RB26 piston is? Ive also got a piston crown to deck measurement of 3.7mm, is this common?

Thanks for taking the time to respond lads.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • brillo
      Leak from Tokico BM50 Brake Master Cylinder

      By brillo · Posted

      Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Gantai
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By Gantai · Posted

      PXL_20250828_063541093.TS.mp4
    • Gantai
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By Gantai · Posted

      Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • PranK
      R35 GT-R production ends after 18 years

      By PranK · Posted

    • SteveL
      Leak from Tokico BM50 Brake Master Cylinder

      By SteveL · Posted

      I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...