Jump to content
SAU Community

Recommended Posts

It was a streeter, I would have loved to run it down here in the cool qld nights. I know it would make a massive difference having driven my stocker GTR in both summer and winter.

And yes, had the baby seat in and on street rubber, nothing special and at 35psi.

It was making 500hp at the wheels from memory. The acceleration was brutal.

Theres a list on here somewhere.

N1 group A turbos

N1 water and oil pumps

Z32 afms

Tomei cams

044 pump

Sard 720cc

Greddy rail/fpr

OS cam gears

REV I beam rods

Forged pistons

Blitz cooler

Greddy oil cooler

" reloc kit

Big fark off clutch from the boys at Direct

Stainless exh mani

Dumps, nismo front pipe, trust pe2 exhaust and a drift (laugh as you may, but the car made 20rwhp over the trust rear can)

pfc

new set of balls

could be some other stuff, probably is, but forgotten.

  • Like 1

In the write up I saw all electrics where removed o thought as was interior except for dash so stripped ill . Full weight means full interior everything as the car is on the street even street wheels " at least street drag radials " full exhuast, so a regularly street driven car

You're right - he's lost the rear seats but its still only 55kg lighter than my 1800kg C34

"With the passenger seat and belts, stereo, center console, guages and a few other little bits we added for the show and this meeting we are now up to 1745kg race weight, I'm sure a 5kg set of carpets won't hurt any."

__________________

In the write up I saw all electrics where removed o thought as was interior except for dash so stripped ill . Full weight means full interior everything as the car is on the street even street wheels " at least street drag radials " full exhuast, so a regularly street driven car

I would hate to weigh my old girl in , leather full electrics twin sunroof stereo equip lol , oh well after this next round of mods ill chuck her down the track again in full street trim "drive it there drive it back" see what damage I can do

But rips stagea is an absolute weapon I love it !

When you running yours kiwi

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Omg Brake pedal removal.. FML!!
    • I mean, I can confirm the TPS is at 100%.... I can confirm when we installed the TB and setup the cable that the TB was indeed fully open at max pedal travel.. the same 'curve' (WRT MAP vs MAP) existed with the previous setup/TB/manifold as well... No, we did not do a run with no intake connected. I would love to go back in time to do such a run to rule out the intake. It would have also been good to do a run with the airbox lid off. There's a test there where increased IAT vs more available air could be a positive tradeoff. I remember taking the lid off my R34 Turbo setup back in the day and noticing a monster increase, even if IAT's did go up. Could be similar. Hard to test unless I find a very deserted road. 
    • That's actually encouraging to be honest. my motor was rebuild many years ago but it's probably done less than 30,000kms and fucc all limiter or drift, majority street / drag / roll racing. It'll be fine 💪🏼 I don't even have lines or a can for the cam breathers installed yet, there is zero oil residue or splatter on or around them, it drives beautifully so it seems healthy. Just a ticky lifter, yet they're almost brand new oem genuine Nissan and haven't done many kms at all...
    • Have you confirmed the throttle body goes to WOT (and stays there) during the run?
    • I'm having a problem. I think it was mentioned above somewhere but can't see it.  I'm stuck in the cycle of, sand, filler, low spot again, put filler, sand, low spot again, now i put filler again and a thicker portion which seems to have helped but I got low spots in other areas. In the image. Circled in red thats where the original low spot was and the shape is the same as the red out line. I've more or less fixed that (still low spot up the top but now I have low spots where the green circled part is.  Is likely the issue that I didn't start with a course sand paper? I sanded the filler with 240 to reduce the risk of not going to far but maybe the issue is that I'm only taking off enough material to remove some of the filler but not the high spots. I now started sanding with 120 and I think I'm seeing a difference. I did fix one dent the other 2 are f**ked and seems like I made another low spot which is indicated by the furthest green circle on the left handside. Any thoughts and solutions?   Also second image. All of these rock chips, can they be filled in with primer or do i need to fill them all with filler/putty? So many rock chips on mine lol.
×
×
  • Create New...