Jump to content
SAU Community

Recommended Posts

Some days it will drive for hours with no problem. Other times it will shut of 4-5 times in the space of a minute. There is no warning when this happens and you literally do not know 1 second beforehand. There is a very slight engine stumble sometimes but 99% of the time you cannot regain it even if you floor it, it acts like a kill switch. You can shift to neutral and restart the car. It may drive for hours or switch of 1 second after you restart it.

What I have done so far.

Replaced fuel pump and fuel filter with brand new units

Changed spark plugs and checked coils.

Checked some vacuum lines

Cleaned MAF sensor

CHanged Crank angle sensor (its a the black plastic unit from a R34 with the half moon because its a late series 2 aka series 3)

The car is fitted with both an immoboliser and turbo timer. I suspect these may be a culprit. Any common fault I should check before I pull these out?

The car is a late 1998 R33 gts-t.

Link to comment
https://www.sau.com.au/forums/topic/421766-r33-suddenly-shuts-of-while-driving/
Share on other sites

I had a problem like this but it was after i changed my turbo inlet pipe. My MAF was suffering from reversion BIG time cuasing it to spazz out and shut off. I could almost ALWAYS make it shutt off while going up a hill and then pushing in the clutch to let the RPMs drop.

Ok guys after taking out the turbo timer and immoboliser, the problem is still exactly the same, which is a shame because now those units have to go back in and it was all for nothing.

Scotty nm35, The fuel pump is this one http://www.ebay.com.au/itm/Performance-Fuel-Pump-Skyline-RB20-RB25-R32-R33-R34-/120568439688?pt=AU_Car_Parts_Accessories&hash=item1c12706388

The relay used is the same as the stock unit. Only the bracket had to be really modded.

GTR nation, the old fuel pump DID make a whining loud whining noise, the new one does not. Have not monitored fuel pump volatge when this happens. Would need some kind of digital data logger as it may take as long as a day to turn of and you cant keep your eyes glued to the multimeter.

I am going to try a new MAF unit next but its very frustarting. Should have taken firestorms advice but it may end up doing the same thing with a new maf. Guess it was the easiest thing to try first though.

Edited by sonicz

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
×
×
  • Create New...