Jump to content
SAU Community

Fs: R32 & S2 R33 Parts Must Go! Make An Offer!

lteh
 Share

Recommended Posts

lteh Enthusiast

lteh

Posted
Posted

Hey everyone,



I am wrecking a S2 R33 GTS T so have a whole heap of spare parts ready to go!



Check out this list below for parts and prices, if there is anything that you need but don't see here then just ask. I may have it.




R33


S2 Rear cradle inc drive shaft/brakes/cables


$200


S2 R33 Doors


$150 each


S2 R33 Boot with spoiler and hinges


$200


S2 R33 Bonnet


$300


S2 R33 Front Seats


$80


S2 R33 Rear seats


$35


R33 Rear Bumper


$100


R33 Stock Cooler


$80


R33 Front Rio


$50


R33 RHF Guard


$100


S2 R33 RH Side Skirt


$50


S2 R33 Door trims


$20


R33 Switch pack rits


$50


RB25DET Ignition coils & Plugs


$100


R33 RHF Fog Light/Indicator


$100


Seatbelts


$50


RB Radiator


$20




S2 R33 Headlight


$400 pair


S2 R33 Grill, Skyline Plate


$30


S2 R33 Centre Console


$30


S2 R33 Tail lights


$500 pair


S2 R33 Washer Bottle


$20


S2 R33 Coolant overflow


$20


S2 R33 Rear pods


$80 pair


S2 R33 Glove Box


$30


S2 R33 Boot insert


$30


S2 R33 Speedo


$50


S2 R33 Centre Dash


$50


S2 R33 Dash Surround


$50


S2 R33 Windscreen Wipers


$30


S2 R33 Suspension


$100


S2 R33 RH Control arms – Upper & Lower


$100


S2 R33 Rear steering rack


$50


S2 R33 Rear Strut


$50


S2 R33 Door Inserts


$50


S2 R33 Parcel Tray


$50


S2 R33 Air box


$150


S2 R33 Break Booster


$50


S2 R33 Hand brake


$40


S2 R33 Clutch slave & Pedal Box


$50


S2 R33 Front Steering rack


$50


S2 R33 Front Cradle


$100


S2 R33 Sway Bar & connection part


$70



R32


R32 Diff


$300


R32 Front Brakes and vertical link


$200


RB20DET Engine no loom


$400


Rb20DET Gear Box


$200




All prices are negotiable, make an offer. Need these parts gone!





Cheers,


Leong



0401 526 517


[email protected]

Coatsy Rookie

Coatsy

Posted
Posted

Do you have a front strut brace ? also i am interested in door trims and other interior bits eg sun visors etc if in good not faded condition can inspect tomorrow afternoon

  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • myrbgivesmeheadaches
      RB25DET NEO Cylinder Head

      By myrbgivesmeheadaches · Posted

      Did this end up working? Did you take some pictures?
    • Duncan
      V37 Suspension change

      By Duncan · Posted

      And finally, the front lower mount. It was doubly weird. Firstly, the lower mount is held in with a bracket that has 3 bolts (it also acts as the steering lock stop), and then a nut on the shock lower mount itself. So, remove the 3x 14mm head bolts , then the 17mm nut that holds the shock in. From there, you can't actually remove the shock from the lower mount bolt (took me a while to work that out....) Sadly I don't have a pic of the other side, but the swaybar mounts to the same bolt that holds the shock in. You need to push that swaybar mount/bolt back so the shock can be pulled out past the lower control arm.  In this pic you can see the bolt partly pushed back, but it had to go further than that to release the shock. Once the shock is out, putting the new one in is "reverse of disassembly". Put the top of the shock through at least one hole and put a nut on loosely to hold it in place. Put the lower end in place and push the swaybar mount / shock bolt back in place, then loosely attach the other 2 top nuts. Bolt the bracket back in place with the 14mm head bolts and finally put the nut onto the lower bolt. Done....you have new suspension on your v37!
    • Duncan
      V37 Suspension change

      By Duncan · Posted

      And now to the front.  No pics of the 3 nuts holding the front struts on, they are easy to spot. Undo 2 and leave the closest one on loosely. Underneath we have to deal with the wiring again, but this time its worse because the plug is behind the guard liner. You'll have to decide how much of the guard liner to remove, I undid the lower liner's top, inside and lower clips, but didn't pull it full off the guard. Same issue undoing the plug as at the rear, you need to firmly push the release clip from below while equally firmly gripping the plug body and pulling it out of  the socket. I used my fancy electrical disconnect pliers to get in there There is also one clip for the wiring, unlike at the rear I could not get behind it so just had to lever it up and out.....not in great condition to re-use in future.
    • Duncan
      V37 Suspension change

      By Duncan · Posted

      Onto the rear lower shock mount. It's worth starting with a decent degrease to remove 10+ years of road grime, and perhaps also spray a penetrating oil on the shock lower nut. Don't forget to include the shock wiring and plug in the clean.... Deal with the wiring first; you need to release 2 clips where the wiring goes into the bracket (use long nose pliers behind the bracket to compress the clip so you can reuse it), and the rubber mount slides out, then release the plug.  I found it very hard to unplug, from underneath you can compress the tab with a screwdriver or similar, and gently but firmly pull the plug out of the socket (regular pliers may help but don't put too much pressure on the plastic. The lower mount is straightforward, 17mm nut and you can pull the shock out. As I wasn't putting a standard shock back in, I gave the car side wiring socket a generous gob of dialectric grease to keep crap out in the future. Putting the new shock in is straightforward, feed it into at least 1 of the bolt holes at the top and reach around to put a nut on it to hold it up. Then put on the other 2 top nuts loosely and put the shock onto the lower mounting bolt (you may need to lift the hub a little if the new shock is shorter). Tighten the lower nut and 3 upper nuts and you are done. In my case the BC Racing shocks came assembled for the fronts, but the rears needed to re-use the factory strut tops. For that you need spring compressors to take the pressure off the top nut (they are compressed enough when the spring can move between the top and bottom spring seats. Then a 17mm ring spanner to undo the nut while using an 8mm open spanner to stop the shaft turning (or, if you are really lucky you might get it off with a rattle gun).
    • Duncan
      V37 Suspension change

      By Duncan · Posted

      You will now be able to lift the parcel shelf trim enough to get to the shock cover bolts; if you need to full remove the parcel shelf trim for some reason you also remove the escutcheons around the rear seat release and you will have to unplug the high stop light wiring from the boot. Next up is removal of the bracket; 6 nuts and a bolt Good news, you've finally got to the strut top! Remove the dust cover and the 3 shock mount nuts (perhaps leave 1 on lightly for now....) Same on the other side, but easier now you've done it all before
×
×
  • Create New...