Jump to content
SAU Community

Recommended Posts

Intake done in December. I think the ping was before the intakes went in.

Even if it was after...wouldnt the ECU be picking up the different intake and adjust accordingly? I reset the ECU a couple of times since then.

Ping only at low revs...1.8k to 2.3k? higher revs/speeds no ping.

Link to comment
https://www.sau.com.au/forums/topic/423199-ping/#findComment-6809879
Share on other sites

Nope, have not changed spark plugs/fuel pump at all.

Got the car Nov 2012. Car is a 2007 V36. Got it with 36k kms on the clock.

I'll try United P100 and see what happens. Will try to clean MAF and throttle body on the weekend and proceed to spark plugs and fuel pump if all fails...

Is there anything I am missing? Should I try stock air intakes?

Link to comment
https://www.sau.com.au/forums/topic/423199-ping/#findComment-6809912
Share on other sites

Maybe try running some Subaru upper engine cleaner through it? Get rid of some gunk built up in there (and give you a nice clean intake manifold while you are at it - might not fix it, but for under $20 it is worth a try) My V35 ran beautifully afterwards

Link to comment
https://www.sau.com.au/forums/topic/423199-ping/#findComment-6810137
Share on other sites

It also depends on where you bought it as to whether it really has 36k on the clock - it costs under $100 to get this changed. If you have more km on the clock, there are other things that could be more built up in the engine or things that could be wrong. Obviously at 36k it should be basically a brand new car ...

Link to comment
https://www.sau.com.au/forums/topic/423199-ping/#findComment-6810198
Share on other sites

Ok ill try checking the AFM and the cleaner. I dump in Nulon Fuel System Cleaner and 44l of P100 last night. Lets see what happens over the next few days.

I bought the car on auction from Japan. It was checked for genuine KMs by computer system. Whether or not it's genuine, can't really be that sure but yes essentially the whole car looks brand new and nothing was modded or been touched.

Link to comment
https://www.sau.com.au/forums/topic/423199-ping/#findComment-6810623
Share on other sites

Could the the timing yes, one of the more common causes...

Mine has zero mods, its just my daily and I haven't had it for long, but being a high comp engine with Japanese ecu tuning I'm not hugely surprised by the ping on crappier fuel. But I will look at spark plugs and intake clean soon

The Mirage on the other hand has been driving me nuts. I have changed the plugs, plug leads, dizzy cap, rotor, fuel filter, air filter, checked the timing, three rounds of intake cleaning (two at home and one with a pro machine) and full bench injector clean with new o rings etc... yet, still pings :rolleyes:

Next step - colder plugs and oxy sensor. No luck with cheap OBD2 adaptor either

Link to comment
https://www.sau.com.au/forums/topic/423199-ping/#findComment-6813062
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Grind them off, drill them out. Repair any rust on the other side. Start again from scratch.
    • Big R34 GTR parts cleanout. I have a lot of stuff collected over the last 14 years and my missus is giving me hard time. Make my life easy.   Nismo GT carbon fibre diffuser fins (discontinued)  NEW  $2900 Garage Defend Stingray canards carbon fibre  NEW  $1300  Top Secret G Force carbon fibre front diffuser  NEW  $2000  Haltech Elite 2500  NEW  $2500  Haltech Platinum Pro R34 GTR   USED  $1400  Apex’I power FC D'jetro + hand controller R34 GTR   USED  $1400  Nissan OEM BNR34 ECU  USED   $1000  HKS EVC 6  USED  $600  Blitz dual SBC ID boost controller.  USED  $350  TRE 255 LPH Fuel pump  NEW  $100  Fujitsubo  Super Ti exhaust  USED  $2700  Tomei Expreme Ti exhaust  USED  $2000  Trust stainless steel front pipe  USED  $1000  Apex’I super suction kit  USED $400  BC BR coilovers  USED  $600  Hardrace front upper camber kit. USED  $300  Garret 2860-5 turbos –  one good, one needs reco USED  $1000  Nissan OEM Toshiba MFD Screen replacement  NEW  $450  Nissan OEM BNR34 Series II front passenger seat  USED (mint) $5000   Nissan OEM BNR34 front bar in TV2  USED  $1000  Nissan OEM BNR34 front lower air spoiler  USED  $900  Nissan OEM BNR34 front lower air spoiler (painted)  USED  $900  Nismo front indicator (clear) USED  $80 Nissan OEM BNR34 radiator  USED $500  Nissan OEM BNR34 turbos  USED  $500  Nissan OEM BNR34 intercooler USED  $800  Nissan OEM BNR34 front swaybar   USED  $500  Nissan OEM BNR34 intake pipes   USED  $400    Also have a square set of uber rare Volk CE28n in 19*10 +22. Not really keen to sell these but make a high enough offer and maybe I will. If you don't know how much these usually sell for don't bother.   PM for pics.  Pickup Chadstone VIC or postage at buyer's expense.
    • Thanks Mate, I did know you could do that but i know there is a pump out there that you can bolt on and it all lines up. I was told about it and then forgot the model, I figure if i am pulling it apart i will just put a new one on 
    • You can also remove the veins from the HICAS portion of your existing pump. 
    • Trying to swap the rear subframe on my R34 and can't remove the L-shaped stay brackets between the front subframe mounts and the sill/chassis. I'm in the UK so rust is a problem. I've used loads of WD40 and then Tunap 103 for days beforehand. I backed off the bolts forward a bit, backward a bit repeatedly for ages to try and avoid snapping. They have all moved a few full turns. The one I've spent most time on has come loose and I can turn with fingers, and it will pull down and push up 2-3mm. But it won't come out. I can tighten it back up and loosen it off again repeatedly but it still won't come out. I assumed there's a captive nut inside but if that's broken loose then I can't understand why I can always tighten the bolt back up - I'd expect it to just spin both ways. Any ideas what's happening here? I can't visualise what's inside there to cause this.
×
×
  • Create New...