Jump to content
SAU Community

Recommended Posts

Correct. They slip together and have two bolts holding them.

Its a recognised method of attaching legs and perfectly fine to do but a fully welded joint is best.

The way AGI do theirs is a better design with the 44mm tube and 38mm tube slid inside it. The fence post clamp together joins are rubbish.

So what's your equivalent product then?

I was considering that cage with the two diagonals (assuming it adds head protection for both occupants in a roll). Then welding in some base plates to bolt too. That's 880 delivered and painted.

What would your cage, painted and freighted cost and what work would I have to do when it gets here.

I wouldn't put both diagonals in the hoop.

One in the hoop and one in the rear legs with a harness bar in the main hoop as well.

Main hoop

Two rear legs

Harness bar

Hoop diagonal

Rear leg diagonal

12.9 high tensile bolts

Plates to be welded to body.

TIG welded (ER70s-2 filler rod)

German CDS material.

Ill do that cage for $770 plus the deliver cost which would probably be $140-$150.

When you get it you'll need to remove the seats and centre console

Remove the seat belts and rear trim etc.

Weld in the base plates for the main hoop

Drill holes for the rear leg plates

Bolt the cage to the base plates and then reinstall the seats, harness and trim etc.

OK cool, thanks for your help so far.

So to confirm, that cage comes as one piece fully welded and the only bolts are the ones used to fix it to the welded plates the car (are the plates meant to be welded for the backstays as well?).

Also, do you do/know what the best option is for lowering the seat.

My helmet sits too close to the roof at the moment.

I can see ways to get it lower but wondered if you offered something off the shelf.

Also, I assume it's most beneficial to TIG weld the plates in or is MIG sufficient for that weld?


Edited by ActionDan

Further to my questions above, another member has contacted me explaining that he'd like a cage too so with that in mind, is there the possibility of a discount on the cage or freight if we order 2? Would they both fit on one pallet etc?

He's currently waiting for pics from Roy, but if you have any now is a good time to throw some up.

No off the shelf solutions for seats I'm afraid.

Mig welding plates to the floor is the only way. TIG welding to a floor pan is very difficult and ugly.

I'm sure two cages could go on one pallet yes.

I don't actually have photos of troys cage. I do that many I don't normally take photos anymore.

I think there may be some in his build thread though.

Does this look like it?

gallery_20349_4009_25906.jpg

I demand $50 from anyone that posts pics of my car :)

Brad must have taken that pic as it doesnt look like one of mine.

It is SCHMICK! I am not saying that because its my car. I am not saying that because Risking is on the forum. I had the BD cage and was happy with it generally for the 2 or so years I had it. It isnt a question of better or worse etc. I got what I asked for from BD. If I had of articulated my requirements better I would have paid more and probably got what I was after but was mostly scared of rendering the back seat completely useless for storage of tyres and bags on a trip to the track

When I knew what I really wanted Brad was able to give it to me. I can still fit two 17" rims in the back seat. two in the passenger seat and fuel in the boot. When a recliner seat is in it goes a fair way back for some zzzzz when I am doing the Melb-Syd drive at night. Its all I could ask for since my thing is only a club car and needs to be driven on a daily basis

What do people think of something like this harness wise?



http://www.revolutionracegear.com.au/index.php?PCID=10413&PSO=245&PSID=9193133&PSV=Primary&CDO=



I thought at least 5pt for the anti submarine belt.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Actually everyone on the roads was really well behaved. The only person that did any minor tailgating was a local hoon in a Turbo Focus. Unfortunately we weren't going the same way so there was no grand initial D touge battle. Lots of people pulled over and let me through. The amount of "Hey man nice car, omg skyline, nice 34 man woo" was suprising. Like really suprising. Like almost annoying. My partner was obviously surprised, she'd never seen anyone in the real world point out the car/like the car/want to chat about the car before, so to have like 3 people per day mention it was notable, I could finally say SEE? SOMEONE THINKS THEY'RE COOL. Everyone was also pretty suprised about the weather. Every day was dry and about ~13-14C. Mount Wellington had a sign that said they close the gates at 9pm and I was heading up there at about ~7:30. It was VERY apparent that conditions were getting significantly worse by the minute on the way up and down. The road on the mountain was terrible though, it's no driving road. I have various suspension related questions now. Luckily it was only about 20 minutes from where we were staying to the top of the mountain as said Google maps. We only had the 2 nights in Hobart. We went to the Farm Gate Market though which was really good - And went down to the Hastings Thermal springs/caves down there during the day. I'd definitely be up for going back again, so luckily there's a few more sights yet to see. Didn't get to do the west coast/queenstown/cradle mountain so this was supposed to be a 'scouting' trip anyway of sorts if I were to one day do/take part in/organize a more car-focused trip. As for the boat, it wasn't bad. Well it was bad, but not in the way you're thinking. We did the night trip which leaves at 6:45 (though you have to be there ~2 hours earlier) and arrives the next morning at about 6am. There is nothing to do on the ship. If you plan accordingly and bring a book/tablet/show to watch/charger you can just chill out, take some Travacalm and just sleep through it. The food there is an extremely basic buffet that costs $32 a plate, or $14 for a $3 pizza. The way back we had a travel kettle and a few different types of cup noodles and made our own tea/coffee in the room. This was a far superior way to do it. At the very least book one of the rooms with beds. I guess as we were in the off season we didn't have room mates. You get an option for rooms with 4 beds (2x bunks) or a room with just the two bottom beds. There's also some option for a deluxe queen bed but it's much pricer. We've been on sleeper trains in Asia before so we figured this is similar (and it was)
    • You just gotta be really, really, really clear and decisive with what you want your end product to be. 99% of people who want this conversion aren't "I want to run a 295 front tyre!" so they don't really need the widebody. They just want the OEM body to look a little less dumpy, so bonnet, bar, skirts job done with some camber, stretch, slam. It's when you want that, but then decide to pivot later you get big problems. See also if you're willing to get an all in one fibreglass bar, and you're willing to accept fibreglass problems like cracking the entire item on a driveway, instead of just a piece attached to the bottom, etc etc etc. Decide this all before buyin'.
    • After @Kinkstaah debacle, I'd never want to try and get it right 😛
    • The hood lines up with the fenders. The front bar doesn't perfectly line up with the fenders where the wheel arch is. You have to 'squeeze' the front bar 'in' as it wants to naturally flare out and be longer on the sides. There's a few threads where people notice this when they only swap a GTR style bumper and front bar. Unless you have genuine OEM items - you may be better served getting conversion kits. There are GTT bumpers to fit GTR hoods. There are GTR hoods (non genuine) to fit the GTT bracketry. MAY  
×
×
  • Create New...