Jump to content
SAU Community

Recommended Posts

VQ is still sitting on workshop floor, but we have since turned back to utilising the existing SR instead :) Wanting something more brutal than linear.

Ah ok, so no result expected then? HTA on the SR? :P

VQ is still sitting on workshop floor, but we have since turned back to utilising the existing SR instead :) Wanting something more brutal than linear.

25/30 with 3076 .82 ex gate.... do it... power fkn everywhere...

I dunno they're all the same..."which turbo for my rb25"...It seems nobody knows the answer...

3076 + RB25 is a match in every way! Its tried and tested and a good all round package...... The GTX version seems to have been a flop for those wanting daily response...... That HTA concept sounds good but no real results as yet to go off...... Precision seems to have good options like the 5558 which responds well on Kurtis's 34......... Kando and HG have good options too......... LOTS of good turbos for RB25 :yes:

3076 + RB25 is a match in every way! Its tried and tested and a good all round package...... The GTX version seems to have been a flop for those wanting daily response...... That HTA concept sounds good but no real results as yet to go off...... Precision seems to have good options like the 5558 which responds well on Kurtis's 34......... Kando and HG have good options too......... LOTS of good turbos for RB25 :yes:

yes I know there is lots of choices, but which turbo for my rb25???

yes I know there is lots of choices, but which turbo for my rb25???

Well Lithium's neck is on the line so he obviously knows something about these FP turbos..... Try one and report back so i can copy if it works :laugh:

Freddy plenum with Q45 TB..500$$.

vs

Plazman and TB 2000$

I know which i would choose :yes:

I discovered the hard way with the Freddy that you need to get the face machined flat before installation.... coolant coming out of the exhaust is not good. Lots of stress and thought the engine was fkd.

I tried 2 of them with similar results till I machined it and problems went away... so if you Freddy it, just make sure it is machined flat!!

I discovered the hard way with the Freddy that you need to get the face machined flat before installation.... coolant coming out of the exhaust is not good. Lots of stress and thought the engine was fkd.

I tried 2 of them with similar results till I machined it and problems went away... so if you Freddy it, just make sure it is machined flat!!

You get what you pay for ;)

well any body that has read this forum thoroughly would know this and get it machined...others would just hand a big pile of cash to JEM and let them worry about it... ;)

Haha ouch! I handed it to Plazmaman thankyou very much :laugh:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So stock ECU does not like anything above 10 psi?  That Nistune one is just for "try" if it will be any different, I know it need to be tune for that. I know but YOU may know about these problem but i/we dont. They few little Skylines here let alone people who know anything about tham so that is why iam asking here  
    • So now we have a radiator with no attachments whatsoever. It lifts up with a particularly tight spot between the drivers side air box mount and the lower radiator outlet, but if you've got this far you will sort that too. This is the lower mounts with the rad out so you can see where the rubber bushes go, it is a straight shot upwards Done! Assembly is the reverse of disassembly, with blood less likely to be shed.
    • Right, onto the second last trick. The Air Con condenser is mounted to the front of the radiator and stays in the car when the radiator is removed. There are 2x 10mm headed self tappers holding the top of the condenser to the radiator, remove those The bottom of the condenser is attached to the radiator with clips. You need to lift the condenser out of those clips and clear (up, then forward). f**ked if  could work out how to do that last bit with the front bumper on. I hope you can, and you share the trick.  Bumper removal probably deserves its own thread one day once I've recovered the will to live, but basically you need to remove the wheels, front inner guard liners (clips and 10mm headed bolts), the self tapper between the guard and the bumper at the rearmost point of the bumper (same as an R32 that bit), any remaining clips at the top/front of the grill, an absolute bastard design with a plate that holds the top of the bumper above the headlight each side (only 1 bolt which is tricky to get to, but the plate catches 2 places on the bumper and must be removed....carefully!) and push clips between the bumper and guard under the headlight. If you've done all that you will be faced with wiring for the fog lights on both sides and in ADM Q50 RS at least, 4 nasty tight plugs on the driver's side for the ADAS stuff. So, the clips at the bottom look like this on drivers side (looking from the front) And on the passenger side (also from the front), you can see this one is already out Clearance on both of these are super tight; the condenser needs to move up but the upper rad support mount prevents that, and the radiator can't move down far because it is (rubber) mounted. Once you achieve the impossible and drop the condenser off those mounts so it does not stop the rad moving, you are good to go
    • OK, next the shroud needs to come off and there are a couple of tricks. Firstly, there is a loom from near the passenger side headlight to the fans, coolant temp sensor etc and there is no plug to undo.  In my case I was OK to leave the shroud on top of the engine so I just undid the passenger side fan plug and about 10 of the clips which gave enough free wire to put it aside. The fan plugs were super tight, the trick I used was a small falt screwdriver to push down on the release tab, then a larger flat screwdriver to lever the plug out of the fan unit....be careful with how much force you apply! If you need to remove the shroud altogether for some reason you will have to deal with all the plugs (tight) and clips (brittle)....good luck. I removed all of the clips and replaced them with cable ties that I will just cut next time. Also, in the Red Sport / 400R at least, the intake heat exchanger reservoir hose is bolted to the shroud in 2 places with 10mm headed bolts; so remove them (the hose stays in the car; no need to undo it at the t fittings down at the radiator lower mount. Once you've dealt with the HX hose and the wiring loom, there are 3x 10mm headed self tappers holding the top of the shroud to the radiator; remove those.   The shroud then lifts out of the bottom mounts where it sits on the radiator, up and onto the engine out of the way. Simples
    • Ok, disregard my “rate them” comment, sorry for my unrealistic input
×
×
  • Create New...