Jump to content
SAU Community

Recommended Posts

Hi All,

This is firstly an EOI for a Group Buy (GB).
~ Serious buyers for this Group buy EOI starts NOW and closes 24th May 2013. Think before adding your name in this thread, as it will be the GB thread if I get enough interest.

~ Decision to proceed or not will be made by me on the 24th based on interest shown.

~ Discussions in relation to comparisons, tech specs, merits and costs of other brands and suppliers to be held in the General section. This is the EOI/GB thread for Nismo Twin Plates, either you want one or you don't (Harsh ?).

Group buy if run will be 24th of May ~ Closing 7th of June 2013. "show me the money"

Recently my clutch got lunched and I needed a new one. Did some research and settled on the Nismo Super Coppermix Twin plate - Competition.

A lot of good information and reviews on SAU. One issue I faced was timeframe as I didn't want my GTR off the road for 2-3weeks. Anyway that's another story.

For now I have a new 'other brand' twin plate. However I am still keen to buy one of these and potentially on sell my new one. I'll decide over the next few weeks.

With the current exchange rate Prices are good for Aussies (and I guarantee it wont last too much longer - read over by Xmas). It's starting now to set up for the worse :(

EOI for NISMO - Supper Coppermix Twin & Comp Clutches; BNR32/BCNR33 - not BNR34 but with enough genuine interest I will get prices.

1. Nismo Super Coppermix Twin Plate; 471kw/640hp, 950kg pressure, 2.08kg lighter than stock

- Allowable torque of 84 kgfm for dynamic friction (Stactic friction:143 kgfm) Handles an estimated allowable power of 670 ps

Price is estimated at $1700 delivered

2. Nismo Super Coppermix Twin plate Competition spec; 574kw/780hp, 1150kg pressure, 2.08kg lighter than stock.

Price is estimated at $1800 delivered

Note: Prices are very good current estimates.

Based on Volume, Shipping method and AUD conversion on the day it may be even cheaper :woot:

The above prices include EMS freight. Cheaper still using SAL or SEA.

Freight rates on current exchange are as follows..

EMS : $235

SAL : $187

SEA : $100 (so therefore if you can wait subtract another $135)

One of the advantages is these clutches 'feel' very close to OEM but handle a truck load more power.

Delivery - 2-3 weeks GB closing using EMS. ( up to 1 week from Manufacturer to supplier, 1 week to ship (4-6days), +1 week to account for any delays which may be experienced and unforseen)

Supplier: To be announced on GB closing date and prices locked down.

Any questions please PM me. :yes:

Cheers

Richard

is that 640hp at the wheels ?

I'm currently making 474 RWKW (630 rwhp) and its been in the car for 7 years. I really think those figures are conservative. Never had any issue with it slipping.

Estimated Prices only - may fluctuate with AUD until orders confirmed and then placed.

Therefore I have added a little risk factor pricing in the attached spread sheet.

Edited by Sinista32

Minor Update

- should have something pretty firm on Monday eve. Decision to go/no go on the GB.

- so far 5 have shown interest. Hopefully these are committed.

- > Anymore for anymore ?

After looking at a number of online shops, contacting them to see if they can do better on a group buy, prices don't differ very much at all with a few of our well known and respected individual suppliers.

In fact every one is pretty much the same at the moment.

Unless some really good pricing comes back from a number of enquiries this GB will be terminated. Sorry., seemed good at the time.

As it appears I can't do much better than you could do yourself :(

I have my personal preferred supplier who will get back to me tomorrow evening with a final price.

If anyone else has someone on the inside and can do a deal 'WE' would like to hear from you (PM me) !

Will go 1700 delivered on mine below if anyone is keen and the group buy doesn't pan out...used literally less than 500kms

http://www.skylinesaustralia.com/forums/topic/425688-nismo-super-coppermix-twin-plate-clutch-suit-r32-gtr/#entry6865785

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
×
×
  • Create New...