Jump to content
SAU Community

Recommended Posts

I am about to wire in a solenoid for my rb25, the factory wiring has been removed/shortened/missing.

I have found the factory output wire on the ecu connector but need +12V Ign.

Am I able to use either pin 49/59 as they are switched from eccs relay for the +12V or am I better of running a wire from the Ignition?

Why not look at the original wiring diagram?

As above, wire the mac valve to the original solenoid wiring

got the diagrams and looked over them that's not the issue

who ever did the engine conversion originally, removed half the pins from the engine loom.

I've got the wire on the ecu for the solenoid now I just need +12V. just wanted to keep it neat by using a +12v from ecu

But that's the point. Find out, from the original wiring diagrams, where the factory sourced their 12V from, and do the same as that. They won't have done whatever they did for a bad reason. They would have done it for a good reason. If you source it from the ECU you might introduce some nasty noise into the ECU (from the valve square waving on and off) or you might draw more current than it can handle on that line or any number of other foreseeable (or not foreseeable) possible bad things.

Follow the factory's lead, avoid those possible problems.

  • 5 months later...

Just another question does the MAC solenoid have an outputing voltage or its and inputing voltage. Im asking this because if i sourced the 12V IGN source from the factory solenoid. Where does the second wire go analog/ digital input or ???

The solenoid doesn't care how it is switched. You could either give it permanent 12V on one side and switch it on the earth side, or give it permanent earth on one side and switch 12V onto it from the other.

BUUUUUT...... What really matters is how the ECU wants to switch it. And from what your first post says (assuming you're correct), the ECU will switch the earth side of the solenoid to earth. So the second wire from the MAC valve just connects to the boost control pin on the ECU.

ok i wasnt understanding how it was completing the circuit without the ground. So its connected by 12v then the second wire goes to the ecu boost controll pin. How is the ECU controlling the solenoid, is it applying varied voltage to the solenoid.

nah this is a different case i have stock wiring. Went to a local meet and was told the same to use stock wiring where the old one was located so thats good if said more than once. Just didnt want to start another thread. Not sure if using thw stock will support the boost by gear functions but for now im happy will just wire it on the stock solenoid

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Surely somebody has one in VIC. Have you asked at any shops?  Is this the yearly inspection or did you get a canary?
    • This is where I share pain with you, @Duncan. The move to change so many cooling system pieces to plastic is a killer! Plastic end tanks and a few plastic hose flanges on my car's fail after so little time.  Curious about the need for a bigger rad, is that just for long sessions in the summer or because the car generally needs more cooling?
    • So, that is it! It is a pretty expensive process with the ATF costing 50-100 per 5 litres, and a mechanic will probably charge plenty because they don't want to do it. Still, considering how dirty my fluid was at 120,000klm I think it would be worth doing more like every 80,000 to keep the trans happy, they are very expensive to replace. The job is not that hard if you have the specialist tools so you can save a bit of money and do it yourself!
    • OK, onto filling. So I don't really have any pics, but will describe the process as best I can. The USDM workshop manual also covers it from TM-285 onwards. First, make sure the drain plug (17mm) is snug. Not too tight yet because it is coming off again. Note it does have a copper washer that you could replace or anneal (heat up with a blow torch) to seal nicely. Remove the fill plug, which has an inhex (I think it was 6mm but didn't check). Then, screw in the fill fitting, making sure it has a suitable o-ring (mine came without but I think it is meant to be supplied). It is important that you only screw it in hand tight. I didn't get a good pic of it, but the fill plug leads to a tube about 70mm long inside the transmission. This sets the factory level for fluid in the trans (above the join line for the pan!) and will take about 3l to fill. You then need to connect your fluid pump to the fitting via a hose, and pump in whatever amount of fluid you removed (maybe 3 litres, in my case 7 litres). If you put in more than 3l, it will spill out when you remove the fitting, so do quickly and with a drain pan underneath. Once you have pumped in the required amount of clean ATF, you start the engine and run it for 3 minutes to let the fluid circulate. Don't run it longer and if possible check the fluid temp is under 40oC (Ecutek shows Auto Trans Fluid temp now, or you could use an infrared temp gun on the bottom of the pan). The manual stresses the bit about fluid temperature because it expands when hot an might result in an underfil. So from here, the factory manual says to do the "spill and fill" again, and I did. That is, put an oil pan under the drain plug and undo it with a 17mm spanner, then watch your expensive fluid fall back out again, you should get about 3 litres.  Then, put the drain plug back in, pump 3 litres back in through the fill plug with the fitting and pump, disconnect the fill fitting and replace the fill plug, start the car and run for another 3 minutes (making sure the temp is still under 40oC). The manual then asks for a 3rd "spill and fill" just like above. I also did that and so had put 13l in by now.  This time they want you to keep the engine running and run the transmission through R and D (I hope the wheels are still off the ground!) for a while, and allow the trans temp to get to 40oC, then engine off. Finally, back under the car and undo the fill plug to let the overfill drain out; it will stop running when fluid is at the top of the levelling tube. According to the factory, that is job done! Post that, I reconnected the fill fitting and pumped in an extra 0.5l. AMS says 1.5l overfill is safe, but I started with less to see how it goes, I will add another 1.0 litres later if I'm still not happy with the hot shifts.
    • OK, so regardless of whether you did Step 1 - Spill Step 2 - Trans pan removal Step 3 - TCM removal we are on to the clean and refill. First, have a good look at the oil pan. While you might see dirty oil and some carbony build up (I did), what you don't want to see is any metal particles on the magnets, or sparkles in the oil (thankfully not). Give it all a good clean, particularly the magnets, and put the new gasket on if you have one (or, just cross your fingers) Replacement of the Valve body (if you removed it) is the "reverse of assembly". Thread the electrical socket back up through the trans case, hold the valve body up and put in the bolts you removed, with the correct lengths in the correct locations Torque for the bolts in 8Nm only so I hope you have that torque wrench handy (it feels really loose). Plug the output speed sensor back in and clip the wiring into the 2 clips, replace the spring clip on the TCM socket and plug it back into the car loom. For the pan, the workshop manual states the following order: Again, the torque is 8Nm only.
×
×
  • Create New...