Jump to content
SAU Community

Recommended Posts

LMAO! That is amusing on so many levels right now..

"Happy birthday drifter"..... Cake is modeled on an EVO FP Red turbo LOL

Lol you KNOW that wasn't a fluke, right? :-P

Lol yeah....

Evo drift FTW!

  • 4 weeks later...

hi guys cheers for input, abit of both power and response? maybe after engine goes decide to rebuild it with what ever suits street track use mainly street though as it a daily.

You've effectively regurgitated what you said on the first page - who knows what you mean by power and response. Some people get the giggles off 240kw @ wheels, some people can happily live with full boost at 5500rpm. Get a GT6041, it will make some power and will respond eventually.

I stick by my initial suggestion, anyone who isn't keen to commit on EXACTLY what they are after but want something quick and streetable then I reckon an FP HTA GT3582R would be the perfect thing for an RB26 based GTR. Should be good for 350+kw on pump gas or 400+kw on E85, and good boost by 4000rpm.

Lith , what do you think would happen with a HTA3076R using a bigish - say 1.06 AR turbine housing ?

Hard to say, really - probably be quite noticeably laggier, and going from Bri73y (396rwkw with a VERY free flowing exhaust and stock GTR intercooler) and 34GeeTeeTee (391rwkw with reasonably quiet 3" exhaust + screamer pipe, good FMIC)'s results the compressor and the .82a/r turbine housing are getting to their limits in parallel - so upgrading one end or the other may not give very rewarding results. A 1.06 housing could potentially cause lag that I am not convinced would be justified - it would be an interesting thing to see, but it wouldn't be a thing I'm go out of my way to recommend people try as I'm much more confident that the HTA3582 would offer a safer more acceptable balance of spool and power. Bare in mine the HTA3582 is likely to spool much like the stock GTR turbos (the HTA3076 better than stock) so really makes it hard to end up with a disappointing result, so long as you aren't looking for ~400kw on pump gas or ~450kw on E85... as thumbsucks.

Your thoughts?

Lith , what do you think would happen with a HTA3076R using a bigish - say 1.06 AR turbine housing ?

 

Hard to say, really - probably be quite noticeably laggier, and going from Bri73y (396rwkw with a VERY free flowing exhaust and stock GTR intercooler) and 34GeeTeeTee (391rwkw with reasonably quiet 3" exhaust + screamer pipe, good FMIC)'s results the compressor and the .82a/r turbine housing are getting to their limits in parallel - so upgrading one end or the other may not give very rewarding results.  A 1.06 housing could potentially cause lag that I am not convinced would be justified - it would be an interesting thing to see, but it wouldn't be a thing I'm go out of my way to recommend people try as I'm much more confident that the HTA3582 would offer a safer more acceptable balance of spool and power.  Bare in mine the HTA3582 is likely to spool much like the stock GTR turbos (the HTA3076 better than stock) so really makes it hard to end up with a disappointing result, so long as you aren't looking for over ~400kw on pump gas or ~450kw on E85... as thumbsucks.

 

Your thoughts?

Sent from my GT-I9505 using Tapatalk 2

So you've not really given us any of the input we've asked for in order to make sure you're given the right suggestions, and not paid attention to the recommendations we've offered - then mentioned a different option to what anyone here has mentioned with no "why"? Why does this thread exist, again?

So you've not really given us any of the input we've asked for in order to make sure you're given the right suggestions, and not paid attention to the recommendations we've offered - then mentioned a different option to what anyone here has mentioned with no "why"? Why does this thread exist, again?

:laugh:

What's achievable on standard 26 block with different oil pump and cams etc??

A lot! Depending on what fuel you have!

Fast. Reliable.cost effective. Pick two

Kind of!

What's achievable on standard 26 block with different oil pump and cams etc??

i'd go for 420ish, how long will it probably last?, mostly street use probably quite a while, enter le mans 24hr tomorrow, it'll probably be dead tomorrow :laugh:

i'd go for 420ish, how long will it probably last?, mostly street use probably quite a while, enter le mans 24hr tomorrow, it'll probably be dead tomorrow :laugh:

420 what? hp? Kw? Gigawatts?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...