Jump to content
SAU Community

Recommended Posts

nitto stroker kit

nitto oil pump

nitto head gasket

rrr racing block

peterson dry sump

head package through crd, dirt garage or equivalent.

ross or ati balancer

arp studs throughout

adjustable cam gears

hks t51r turbo

id2000 injectors

larger fuel rail

or

RIPS engine package

or, let us know your goals and budget.

will help decide what to do.

Ive so far purchased cp forged pistons,spool rods,acl bearings,arp studs all round,jun oil pump, just need ideas on cam duration/lift and valve springs also what turbo to run with to get the most out the 26.

all good.

id love to be able to afford their gear too.

maybe one day.

maybe not.

theres a thread currently discussing pretty much this.

cant remember exactly where, bit some were saying you can get a racepace engine(yours rebuilt by them)for 10k incl parts and labour.

may be worth freighting it?

do you need turbo setup?

do you need fuel system?

now we know a rough budget, what do you want/need and what power goals are you aiming for?

Ive so far purchased cp forged pistons,spool rods,acl bearings,arp studs all round,jun oil pump, just need ideas on cam duration/lift and valve springs also what turbo to run with to get the most out the 26.

twins or single?

Be interested in looking into that thread if you happen to come across it.

Im hoping to get enough help through this thread from past experience builds so i know which direction on parts selection i should take on getting good power from a budget.

Am looking at getting rid of the twins and going single so turbo choice also would help.

  • 2 weeks later...

nitto stroker kit

nitto oil pump

nitto head gasket

rrr racing block

peterson dry sump

head package through crd, dirt garage or equivalent.

ross or ati balancer

arp studs throughout

adjustable cam gears

hks t51r turbo

id2000 injectors

larger fuel rail

or

RIPS engine package

or, let us know your goals and budget.

will help decide what to do.

Jesus creepers Luke! RRR block itself is rare as hens teeth yet alone $10k+ to procure .

be better off just getting N1 block from Just Jap cost like 2.6K.

I was under the impression that Dan was not doing engines and ERD anymore? Health Issues Maybe from what I recall?

Dan is still building engines as a sort of private on the side setup, from what i gather, but ERD itself is no more.

Probably a lot less messing around only doing engines.

  • 2 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • perhaps i should have mentioned, I plugged the unit in before i handed over to the electronics repair shop to see what damaged had been caused and the unit worked (ac controls, rear demister etc) bar the lights behind the lcd. i would assume that the diode was only to control lighting and didnt harm anything else i got the unit back from the electronics repair shop and all is well (to a point). The lights are back on and ac controls are working. im still paranoid as i beleive the repairer just put in any zener diode he could find and admitted asking chatgpt if its compatible   i do however have another issue... sometimes when i turn the ignition on, the climate control unit now goes through a diagnostics procedure which normally occurs when you disconnect and reconnect but this may be due to the below   to top everything off, and feel free to shoot me as im just about to do it myself anyway, while i was checking the newly repaired board by plugging in the climate control unit bare without the housing, i believe i may have shorted it on the headunit surround. Climate control unit still works but now the keyless entry doesnt work along with the dome light not turning on when you open the door. to add to this tricky situation, when you start the car and remove the key ( i have a turbo timer so car remains on) the keyless entry works. the dome light also works when you switch to the on position. fuses were checked and all ok ive deduced that the short somehow has messed with the smart entry control module as that is what controls the keyless entry and dome light on door opening   you guys wouldnt happen to have any experience with that topic lmao... im only laughing as its all i can do right now my self diagnosed adhd always gets me in a situation as i have no patience and want to get everything done in shortest amount of time as possible often ignoring crucial steps such as disconnecting battery when stuffing around with electronics or even placing a simple rag over the metallic headunit surround when placing a live pcb board on top of it   FML
    • Bit of a pity we don't have good images of the back/front of the PCB ~ that said, I found a YT vid of a teardown to replace dicky clock switches, and got enough of a glimpse to realize this PCB is the front-end to a connected to what I'll call PCBA, and as such this is all digital on this PCB..ergo, battery voltage probably doesn't make an appearance here ; that is, I'd expect them to do something on PCBA wrt power conditioning for the adjustment/display/switch PCB.... ....given what's transpired..ie; some permutation of 12vdc on a 5vdc with or without correct polarity...would explain why the zener said "no" and exploded. The transistor Q5 (M33) is likely to be a digital switching transistor...that is, package has builtin bias resistors to ensure it saturates as soon as base threshold voltage is reached (minimal rise/fall time)....and wrt the question 'what else could've fried?' ....well, I know there's an MCU on this board (display, I/O at a guess), and you hope they isolated it from this scenario...I got my crayons out, it looks a bit like this...   ...not a lot to see, or rather, everything you'd like to see disappears down a via to the other side...base drive for the transistor comes from somewhere else, what this transistor is switching is somewhere else...but the zener circuit is exclusive to all this ~ it's providing a set voltage (current limited by the 1K3 resistor R19)...and disappears somewhere else down the via I marked V out ; if the errant voltage 'jumped' the diode in the millisecond before it exploded, whatever that V out via feeds may have seen a spike... ....I'll just imagine that Q5 was switched off at the time, thus no damage should've been done....but whatever that zener feeds has to be checked... HTH
    • I think Fitmit had some, have a look on there (theyre Australian as well)
    • Hah, fair enough! But if you learn with this one you can drive any other OEM manual. No modern luxury features like auto rev-matching or hillstart assist to give you a false sense of confidence. And a heavy car with not that much torque so it stalls easily. 
×
×
  • Create New...