Jump to content
SAU Community

Recommended Posts

G'day all,
Was going to tackle my stereo system today consisting of Door speakers, Rear Amped 6x9's, Sub, Headunit & Amp.
After learning earlier today that I'm going to HAVE to re-wire my door-speakers, this has set me back a little as I need to get 14g speaker cable.
I feel completely stupid asking this, and I'm certain I've just over-thought on it and have ended up questioning what I think is correct:
I can remove the adapter that's clicked into the stock unit pictured here: (As it holds no use as when I removed the stereo, it's been replaced with one from a wreckers due to writing on the parts in marker etc etc.)

7fd7300f-64a0-4ae0-ac27-baa414543aa9.jpg

I've done stereo installs on ALL my cars but have never come across this, as every stereo I've removed/replaced has always been factory standard.
So I plan to re-wire it to the new loom on the Pioneer DEH Headunit going in, as this is how I best know about doing installs.
It's safe to cut as close to the stock adapter/harness pictured here, and go about wiring these wires to the new harness that came with my Pioneer headunit?:

c8d3456f-49e8-47cb-9b1f-7fdb1efe08ab.jpg


FINALLY
Can anyone tell me which colour is ACCESSORIES/BATTERY/ILLUMINATION on a 1989 R31 GXE Skyline, or supply a Stereo Wiring Diagram for one? As I've searched almost ALL day even thoroughly, through sticky threads with little to no luck.

Thanks in advance.

Link to comment
https://www.sau.com.au/forums/topic/426525-r31-wiring-adapterloom/
Share on other sites

I can remove the adapter that's clicked into the stock unit pictured here: (As it holds no use as when I removed the stereo, it's been replaced with one from a wreckers due to writing on the parts in marker etc etc.)

I don't really understand that question, yes you can unplug it, if you mean will it affect anything, then no it wont.

You don't have to cut into the harness, most auto stores will have a narva 8 pin connector that will fit it, so you can use the standard power and grounds.

Since your only doing the front speakers from the head unit you can also unpin the standard speaker wires and put your new ones in using the pins that came with the connector( there should be a male and female connector in the same pack). It shall look nice and standardish.

I cant remember which wires are which off the top of my head and my car is about 500kms away so I can't check.

But i deduce from your picture that perhaps the two pins on the far right top and bottom are grounds and the one on the top left is a power source of some sort, i'll guess constant because it appears to have a fuse in it.

You should invest in a multimeter (if you don't have one already), a gregorys manual and check out r31skylineclub.com

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Stock ECU (or more accurately stock tune) absolutely refuses to go over 10psi and behaves like you have seen. The Nistune is the same if it is the stock tune. If the Nistune chip has been tuned, the resulting tune could be literally anything for any combination of parts. The Nistune just makes the stock ECU Tunable.
    • So stock ECU does not like anything above 10 psi?  That Nistune one is just for "try" if it will be any different, I know it need to be tune for that. I know but YOU may know about these problem but i/we dont. They few little Skylines here let alone people who know anything about tham so that is why iam asking here  
    • So now we have a radiator with no attachments whatsoever. It lifts up with a particularly tight spot between the drivers side air box mount and the lower radiator outlet, but if you've got this far you will sort that too. This is the lower mounts with the rad out so you can see where the rubber bushes go, it is a straight shot upwards Done! Assembly is the reverse of disassembly, with blood less likely to be shed.
    • Right, onto the second last trick. The Air Con condenser is mounted to the front of the radiator and stays in the car when the radiator is removed. There are 2x 10mm headed self tappers holding the top of the condenser to the radiator, remove those The bottom of the condenser is attached to the radiator with clips. You need to lift the condenser out of those clips and clear (up, then forward). f**ked if  could work out how to do that last bit with the front bumper on. I hope you can, and you share the trick.  Bumper removal probably deserves its own thread one day once I've recovered the will to live, but basically you need to remove the wheels, front inner guard liners (clips and 10mm headed bolts), the self tapper between the guard and the bumper at the rearmost point of the bumper (same as an R32 that bit), any remaining clips at the top/front of the grill, an absolute bastard design with a plate that holds the top of the bumper above the headlight each side (only 1 bolt which is tricky to get to, but the plate catches 2 places on the bumper and must be removed....carefully!) and push clips between the bumper and guard under the headlight. If you've done all that you will be faced with wiring for the fog lights on both sides and in ADM Q50 RS at least, 4 nasty tight plugs on the driver's side for the ADAS stuff. So, the clips at the bottom look like this on drivers side (looking from the front) And on the passenger side (also from the front), you can see this one is already out Clearance on both of these are super tight; the condenser needs to move up but the upper rad support mount prevents that, and the radiator can't move down far because it is (rubber) mounted. Once you achieve the impossible and drop the condenser off those mounts so it does not stop the rad moving, you are good to go
    • OK, next the shroud needs to come off and there are a couple of tricks. Firstly, there is a loom from near the passenger side headlight to the fans, coolant temp sensor etc and there is no plug to undo.  In my case I was OK to leave the shroud on top of the engine so I just undid the passenger side fan plug and about 10 of the clips which gave enough free wire to put it aside. The fan plugs were super tight, the trick I used was a small falt screwdriver to push down on the release tab, then a larger flat screwdriver to lever the plug out of the fan unit....be careful with how much force you apply! If you need to remove the shroud altogether for some reason you will have to deal with all the plugs (tight) and clips (brittle)....good luck. I removed all of the clips and replaced them with cable ties that I will just cut next time. Also, in the Red Sport / 400R at least, the intake heat exchanger reservoir hose is bolted to the shroud in 2 places with 10mm headed bolts; so remove them (the hose stays in the car; no need to undo it at the t fittings down at the radiator lower mount. Once you've dealt with the HX hose and the wiring loom, there are 3x 10mm headed self tappers holding the top of the shroud to the radiator; remove those.   The shroud then lifts out of the bottom mounts where it sits on the radiator, up and onto the engine out of the way. Simples
×
×
  • Create New...