Jump to content
SAU Community

Recommended Posts

So i got another EPA notice in the mail, my second one in the last two months. My exhaust isn't even that loud :(

Question being, second time around, are they any more harsh when it comes to the test? I barely passed with an 88dB(out of 90dB) last time.

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/426880-epad-again/
Share on other sites

  On 12/06/2013 at 8:21 AM, Terry_GT-R34 said:

I don't think they're any more harsh.

Have you offended a neighbour (who might be in the motor trade)?

So in NSW, for example, if a neighbour believes you have a noisy car, they can go to the local authorities and dob you in. You then get an EPA notice in the mail and are required to pass a check/test?

Link to comment
https://www.sau.com.au/forums/topic/426880-epad-again/#findComment-6887713
Share on other sites

Same in Vic. Guilty until proven innocent. I got a letter in the mail, didn't even get pulled over, had to go for full emissions and noise testing. Took two weeks to put the car back to stock - and another two to put it all back on muhahaha.

Link to comment
https://www.sau.com.au/forums/topic/426880-epad-again/#findComment-6887726
Share on other sites

And to add to what Terry said - in NSW there is an actual EPA iPhone app. All you have to do is type in the rego of a smokey/noisey car and press 'send'.

Nek minut, letter in mail.

(As a side note, if you're a car enthusiast in NSW my suggestion would be to download that app, and report as many smokey rust buckets as you can - keep them busy with other things ;-))

Link to comment
https://www.sau.com.au/forums/topic/426880-epad-again/#findComment-6887728
Share on other sites

  On 12/06/2013 at 8:21 AM, Terry_GT-R34 said:

I don't think they're any more harsh.

Have you offended a neighbour (who might be in the motor trade)?

God i hope not, i usually enter my court in the third or fourth gear, but in the letter it does say 'report lodged by an officer of the Victorian police'?

I'll go in for the test and let you guys know how i go with my little gasket mod.

Link to comment
https://www.sau.com.au/forums/topic/426880-epad-again/#findComment-6887765
Share on other sites

We purchased a Diesel landcruiser with an EPA notice which we found out recently... I spoke to the EPA and they said you can get reported repeatedly BUT if you pass the test everytime with the same system (they take photos for proof) the situation is then reported as a nuisance report and I think future ones are investegated.

We failed with 103db lol

Link to comment
https://www.sau.com.au/forums/topic/426880-epad-again/#findComment-6888270
Share on other sites

haha my sister got an EPA a few months back- Opened it up and someone had dobbed in for tossing and object out the window...

then it stated the offense could occur a fine if the police spotted it

i got pinched for exhaust note a few years ago - Was such a pain to get cleared - Days off work, sent me back as my silencer was not welled to the cannon? Never heard of that shit before....

$65 each time for the mechanic to do the testing...

Link to comment
https://www.sau.com.au/forums/topic/426880-epad-again/#findComment-6888350
Share on other sites

  On 12/06/2013 at 10:08 AM, ishyz34 said:

God i hope not, i usually enter my court in the third or fourth gear, but in the letter it does say 'report lodged by an officer of the Victorian police'?

I'll go in for the test and let you guys know how i go with my little gasket mod.

then you were probably on boost going past a cop who was off duty.

It scares me how often this may happen for me either in the skyline or the GSXR here in perth with the hoon laws. Im very alert for cop cars and in 4 yrs have only ever been pulled over once (including the bike and the skyline) and it was for 12 over...

With this EPA thing you guys have over there it sounds like its worth having really quiet exhausts, n no induction, bov, or wastegate noise or you are going to get trouble coming at you...

Edited by jjman
Link to comment
https://www.sau.com.au/forums/topic/426880-epad-again/#findComment-6889434
Share on other sites

Why do you think I have plumb back gate, plumb back bov and NOW silent turbo? Still if a cop wants I am stuffed....

BUT of all things we got done in a farken diesel landcruiser :/

Link to comment
https://www.sau.com.au/forums/topic/426880-epad-again/#findComment-6889474
Share on other sites

Bad luck getting done in the cruiser. Turbo diesel? If it blows black smoke some douche probs dobbed you in. My old 4.2td patrol was loud as shit and blew a bit of smoke but never got done for it... didnt know about this dob in crap we had here in NSW, what a joke lol. Your arch nemesis/ evil neigbour could just play shits on you with it (if you have one haha)

Link to comment
https://www.sau.com.au/forums/topic/426880-epad-again/#findComment-6889744
Share on other sites

I went close to WOT one time at the lights coming back from work (around ~10pm), while there was a cop on a bike a few cars back. They changed lanes & sped up & matched my speed for a bit (I wasn't really speeding anyway) & then turned off & didn't do anything.

Win Win situation. :yes:

Link to comment
https://www.sau.com.au/forums/topic/426880-epad-again/#findComment-6889771
Share on other sites

Is there any way to check the EPA status of a car before purchase?

I understand the "buyer beware" mentality when it comes to things these days so you know who to blame.

However, in this case with the Landcruiser if there is no way to check can you "legally" put that back on the previous owner?

Link to comment
https://www.sau.com.au/forums/topic/426880-epad-again/#findComment-6889832
Share on other sites

  On 13/06/2013 at 3:10 PM, Frosty said:

fark NSW and its B/S laws! almost to the point of not wanting to own a car anymore....

I second this makes me sick reading about all this.. we spend all this time and money on ours cars and it takes one wank to wreck it for you

Link to comment
https://www.sau.com.au/forums/topic/426880-epad-again/#findComment-6889850
Share on other sites

  On 13/06/2013 at 2:43 PM, Bennis said:

Bad luck getting done in the cruiser. Turbo diesel? If it blows black smoke some douche probs dobbed you in. My old 4.2td patrol was loud as shit and blew a bit of smoke but never got done for it... didnt know about this dob in crap we had here in NSW, what a joke lol. Your arch nemesis/ evil neigbour could just play shits on you with it (if you have one haha)

Turbo Diesel yes, NO black smoke at all and one of the cleanest 80 series on the road!

Link to comment
https://www.sau.com.au/forums/topic/426880-epad-again/#findComment-6890151
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi all. Been a while but things are moving along. I just have something that I am wondering about. Since I will use OEM turbo oil pumbing, I got myself a new bolt, the one that goes into the engine block oil feed. As I recall (and see visually) this bolt comes restricted with I think a 1.7mm hole? Not quite sure but it was something around that size. The turbos have 1mm restrictor bolts installed, as necessary due to ball bearings and my higher oil pressures. Can I now just use that OEM bolt with the 1.7mm hole in for the engine block or will this actually be too much oil flow restriction and I have to drill it out first? In my head it would make sense for the bolt to be at least 2mm wide as both turbos take "1mm of oil flow". Do let me know if my logic is flawed here, I just want to make sure I don't kill my turbo bearings with too little oil. Don't know if I can trust the saying I read somewhere that ball bearing turbos essentially only need an oil mist
    • There are several aftermarket options available, from not-too-painful moneyhttps://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35 and  https://justjap.com/products/crank-motorsport-billet-rear-axles-fits-nissan-skyline-r33-gts-t-r34-gt-t?srsltid=AfmBOorQk4xkGUa98kO7v2ePLUiNt-HRrM2AwWNw9mbSIVE1ujBVwY__, all the way up to The Driveshaft Shop https://driveshaftshop.com/skyline-cv-axles/
    • Yeah based on old XRC5964S specs, it looks to be roughly GTX3576R sized? But this 5964S compressor will flow 90lb airflow somewhat similar to the compressors in both the GTX3584RS or G35-1050.. I fully expected the 0.64 rear A/R to choke up top - seems way too small from typical convention - but these are seemingly beneficial over the prior 0.82 results.. Be interesting to see if he comments on the EFR question in that thread - he mentioned in a prior video that BW EFR's were the "cats pajamas 10 years ago", but by the sounds of things all his kits have been using Xona for quite a while now.
    • Yeah it’s still got the oem manual gearbox and clutch, only kinda mods are a blow off valve, coil overs, and a aftermarket intercooler. Also had it for about 2 months now with a lovely midnight purple paint on it.
    • Yeeeppp, been following a lot of the testing on the latest Xona stuff and there are some mental results.  He also went over 1000hp @ 4 hubs on his Mainline with a XRE6364S (63mm) which was also well into the 20psi range before 4000rpm on a 2.5. Crazy stuff. Fwiw the XRE5964S is basically the modern equivalent of their old HTA3582 - would drive nicely enough on an RB25 or 26, but proven capable of a huge amount of power if you want to spicy with rpm tho even at sane boost levels will make stout numbers 
×
×
  • Create New...