Jump to content
SAU Community

Recommended Posts

genuine nissan HICAS tie rods (different to front tie rods!) are about 250$ for both. from nissan. not cheap. but if you go ling long...well...yeah

well if you got a GT-R I wouldn't use ling long, but I own a R33 GTS-t (ling long is acceptable) haha :)

^ maybe he likes HICAS :)

Theoretically it makes sense to have HICAS, and the system was revised in Series III GT-Rs like yours Paul, prior to that HICAS was pretty shit.

I've tossed mine in the bin too, but I own a fridge.

A lock bar doesn't really solve the problem that you probably have anyway. The outer tie rod ends are the spot that wears the most, and a HICAS delete bar leaves those in place. You'd still need to replace them.

Question.....does 5500 rpm relate to a particular road speed at all? HICAS is known to exhibit it's problems at particular speeds because the HICAS computer reaches "panic mode" at those points when given sensors are not working. Steering angle sensor is one that people often accidentally lose when they put a different steering wheel on the car and the hub doesn't have the drive pin for the steering sensor. On my car (last century) it would crank the steering wheel over to the (left? right?) by about 45° when over 80km/h just because no steering sensor. HICAS panic. No steering sensor also meant I couldn't put it into diagnostic mode which made it very hard to work out what was going wrong. The HICAS computer also looks at VSS, and for all I know in the later GTRs it might even be looking at the G sensors. There's lots of things that can make it act flaky.

Try to put it into diagnostics mode (no, I don't know how to do it on your car, only on an R32). Failing that, get a mechanic with a decent scan tool to hook up to the Consult port and see if there are any codes in the HICAS computer. You may have to take it for a drive and trigger the fault to see anything.

Try to put it into diagnostics mode (no, I don't know how to do it on your car, only on an R32). Failing that, get a mechanic with a decent scan tool to hook up to the Consult port and see if there are any codes in the HICAS computer. You may have to take it for a drive and trigger the fault to see anything.

yeah I'm thinking the same

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I don't know it is due to that. It could just be due to load on track being more than a dyno. But it would be nice to rule it out. We're talking a fraction of a second of pulling ~1 degree of timing. So it's not a lot, but I'd rather it be 0... Thicker oil isn't really a "bandaid" if it's oil that is going to run at 125C, is it? It will be thicker at 100 and thus at 125, where the 40 weight may not be as thick as one may like for that use. I already have a big pump that has been ported. They (They in this instance being the guy that built my heads) port them so they flow more at lower RPM but have a bypass spring that I believe is ~70psi. I have seen 70psi of oil pressure up top in the past, before I knew I had this leak. I have a 25 row oil cooler that takes up all the space in the driver side guard. It is interesting that GM themselves recommend 0-30 oil for their Vette applications. Unless you take it to the track where the official word is to put 20-50w oil in there, then take that back out after your track day is done and return to 0-30.
    • Nice, looks great. Nice work getting the factory parts also. Never know when you'll need them.
    • Thanks @jtha7 I will have a look around tomorrow but it is a prick of a spot. These are some photos i tried taking 
    • I take it that the knock retard is from bearings tapping a little tune? Thicker oil is a fragile bandaid. You need a much bigger oil cooler and probably the bigger pump being discussed.
    • Hi @Chupapy i had several leaks from coolant pipes being corroded, i also had one leak on back of the head onto transmission. For me that leak was from the turbo water line. Follow the line to the back of the head The hose and metal pipe had perished these are the best pics I took of it at the time
×
×
  • Create New...