Jump to content
SAU Community

Recommended Posts

If you have HICAS, then it's LSD. Most likely is AR-X models, however the lucky few have it as an option on the Rs/Rx.

The throttle reset is tricky to get right. Go through from the begging, ecu reset, throttle position learn, and then idle learn.

I'm giving the stag some love this weekend - will be cleaning throttle body (idle reset procedure didnt work, idles at 1400 in N), doing fluids in transmission, attessa and diffs. Do the diffs require LSD fluid?

Cleaning the throttle will only make it worse, make sure there are no vac leaks (the PCV hose is a common culprit) and no engine lights as it doesn't set the idle with an error present.

Change the transfer case fluid too. ;)

Cleaning the throttle will only make it worse, make sure there are no vac leaks (the PCV hose is a common culprit) and no engine lights as it doesn't set the idle with an error present.

Change the transfer case fluid too. ;)

Oh - I read some posts on other forums where cleaning the throttle body helped get the idle reset to work. I'll pull it apart and have a look, but i'll be much more cautious after what you've said. Will the check engine light be on in normal driving if i have an error?

I sprayed aerostart on a few hose ends but didnt get any flaring, so couldn't find a leak that way. There is vacuum at idle, so if there's a leak its not huge.

For me attessa = transfer case, so that's in the list. Might do power steering fluid while im at it.

PN-MAD - I went through "Accelerator Pedal Released Position Learning" and "Throttle Valve Closed Position Learning" first - is that what u mean or is ECU reset different?

Yeah, that's what I meant.

It's pretty obvious when it does the idle learn. When hot, it revs up to 1800 rpm, then drops to the point it almost stalls, then goes back up to 600-650 and steadys. It can be hard to nail the timing, but it does work.

Last resort is get Nissan to do it with consult.

So I think I worked out why my M35 keeps throwing the code 1320. I took the coil packs off to change the plugs and half of the plugs were covered in oil on the outside. The tubes look like the seals are leaking and oil is getting past the O rings in the rocker covers.

Has anyone else experienced this? And where would i get rocker cover gaskets and the o rings.

Yes, it's very common.

But oil is an insulator, so shouldn't effect the coil packs. There is two ways of sealing. First buy whole new rocker covers. The seals are integrated. Or, two, try copper seal or something similar on the rocker covers to try to seal them.

Btw, wrong thread?

FYI - got the idle procedure to work - now idles at just over 600, and is completely smooth. Much better. Hopefully ill get more than ~300kms a tank now.... If not, ill swap the o2 sensor(s). ECU code was 0000.

Transmission fluid looked fine on the dipstick so i had thought it was probably ok, but when I dropped it, it was brown (not too dark) and stunk terribly. The transmission sump plug was completely clean, but ill do the transmission fluid again after say 500kms since its only 4 out of 10 litres from the sump each time.

Just get the Transgo shift kit done Stabby, it changes most of the fluid in one hit and is a must do mod for the M35, along with the brake wire cut. It sounds like the trans has been cooking, was there much red powder in the oil pan?

Not sure about red powder - i just dropped the fluid not the pan. Is the plug magnetic? Is the red powder metallic?

I'm trying to NOT mod the stag since its the daily. The GTR is for that stuff. Would you recommend the shift kit and brake mod for all use modes?

Edit:

PN - yep i'm in Sydney. Sounds like the shift kit is just better for any use type - right? I probably wont worry about the cooler tho since full synth fluid handles high temps so much better than non-syth stuff, and I wont be driving the stag too hard.

The trans will be fine in winter, it just needs a helping hand in summer really, to cool the fluid down and help it last. Heat is what kills auto's.

I would recommend the shift kit for any M35, however it's driven. The stock pressures are very low for comfort and soft shifts, but that is what promotes clutch wear. If the clutches go it could cost you 3-4 grand for a build, unless you can pick up a S/H one to replace it.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
×
×
  • Create New...