Jump to content
SAU Community

Recommended Posts

Got a mate's new 25/30 running today but the oil pressure seems to be a lot higher than it should. Was over 100psi at cold idle. It's currently got running in oil in the engine and has 2 x1.5mm oil restrictors to the head and I'm 99% certain a RB25 oil pump. The vct has an external feed to it but isn't wired up. I'm running a 25 pump on my RB30 and its only got around 60psi at cold idle. Is there any logical reason why it would be running such high pressure?

Also the vct feed is a -4 line. Does it need a restrictor in it at all or will it not matter as we most likely won't be wiring it up so the oil will just drain back to the sump

Edited by PSI086
Link to comment
https://www.sau.com.au/forums/topic/427432-rb2530-high-oil-pressure/
Share on other sites

The oil is a Penrite running in 20/50. Going to run a 10w in it once its got a few km's on it and is ready for synthetic though. Might just see what the pressure is like with the proper oil and normal running temperature. I can't see any reason why it would be higher than a normal RB25 as everything is identical besides the lack of oil squirters under the pistons

Just got the car running with the RB20 tune which was in it previously so can't really take advantage of the vct just yet. Will most likely wire it up though. From what I understand it just needs to be activated with an rpm triggered relay?

  • 7 months later...

sorry to bring up the dead guys but im going though the same drama at the moment with my rb25/30 non vct that's just being built and getting tuned

120psi on cold startup and idled at 1500 on penrite running in oil. this seems worrying!!!???? potential to blow seals etc?

im reading this from a auto meter prolite mechanical gauge.

not sure what the warm oil pressure will be just yet as I haven't let it get to that stage yet.

the oil pump is a rb25det pump with billet gears.

block has 2x 1.3mm restrictors and the vct line is disconnected.

ANY IDEAS ON A FIX??

oh shit! that's high for cold start!! once warm that aint to bad! wat oil ?

at what point do we start thinking f**k that's dangerous could blow rear main and front seals etc?

hasn't done any kms, 1st startup was today and after about 10seconds I noticed it was sitting on 120psi at 1500rpm (didn't wana rev any higher plus 1st EVER start up for the engine.

  • 3 months later...

hey all, find any solutions to these 25/30 high oil pressure issues??

my freshly built forged rb25/30 is showing over 100PSI on my autometer mechanical gauge, oil features include:

tomei oil pump

2X1/3mm restrictors

-12 rear head drain

2X-12 sump breathers

2X-12 cam cover breathers

grub screwed VCT feed in head

VCT sensor removed and capped

drilled out oil drains in block

2L accusump

5.5L sump

19row mocal cooler

GREX oil thermostat and oil filter relocation with ryco z145a filter

on penrite running in oil 15w40 it was showing high oil pressure over 100psi on cold start then down to 90 once warm. a tap of the revs to 2500rpm and it went to over 100psi again (gauge only goes to 100psi). after 250kms the oil was drained and a penrite 10w40racing synthetic was put in. once again on cold start over 100psi but once warm it dropped to 80/85psi or there abouts at idle and only went over 100 after 3000rpm

I was thinking of going a lighter viscosity maybe a 5w30synthetic or something? I only use penrite.

could anyone recommend anything?? or does anything look out of place? im a little worried.

I think im going to get a larger scale mechanical gauge to see where there press really sits after 100psi..

I previously had a rb25 pump with billet gears and was showing the same signs

any help would be HUUUUUGELY appreciated im really stumped and worried.

Cheers

Corey

Edited by ScreamerNewbie

If your bearings clearances are all standard then use a standard viscosity oil which I think is a 30 weight?

If you cant get the pressure to drop when warm below say 120psi at full noise where the oil relief is cracked open then you will need to reduce the spring pressure in the bypass of the pump. If you don't want to do that then you can hook up an external Peterson oil pressure regulator between your sandwich plate and oil cooler/filter arrangement and plumb that in so you can regulate the pressure going into the main oil gallery.

  • 3 years later...
On 10/15/2017 at 10:38 PM, pet vl said:

And iam still haveing trouble any idears its my car looking i to changing the spring in the pump HELP

Be more specific...what is your problem? What is the cold oil pressure and how long does it take to drop to say 100 psi?

I see your other post - just post in one place!

See what happens when you compare the spring pressures.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thanks for all the replies fellas. Gonna finish putting it back together and see how it handles the set up. If it starts pinging it’ll be parked.
    • Well, I can recommend the partial AV system translation CD I ordered from Car Audio Workshop in NZ. Whilst it didn't address the date issue, it has conveniently translated on-screen menu items into English, and now allows the GPS-received time to be offset in hours rather than minutes, so I can display Eastern Australian time accurately ( and bump it by another hour when daylight savings starts ).
    • Yuh, if it's 45°C outside, my car is driving in it.
    • I'd be curious to hear more. Otherwise, have you driven a modern x-trail? I wonder how it compares. Here in Australia they are/were popular for rentals and fleet vehicles. I have been in some and my impression was they are bad. But, this may have been very different in the 2000s at a good trim level. Twenty years is plenty of time to make the model worse. I do very much agree with the 2 silver cars in the garage approach. But, not driving because it's too hot would not leave a lot of time in the year for many Australians. I don't think you need to worry too much unless the car has actual issues with overheating. 
    • Back again. I returned to Japan in Jul/Aug to spend time with the car on my birthday and remind myself what all the sacrifice and compromise is for. It happened to line up with the monthly morning meet in Okutama, which I have been wanting to go to for a long time. It's a unique event at a unique spot with really rare, interesting, and quirky cars. It's where all the oldheads and OGs gather. The nighttime scene at DKF certainly has its place and should be experienced if you're into cars, but there's too much bad attention and negativity around it now. IMO the better time is Sunday morning at DKF or Okutama; it's more chill and relaxed. I'm glad I was finally able to go, but not sure it's worth the drive from all the way from Nagoya immediately the day before, unless I was already staying in Tokyo for the days right before the meet, because you have to wake up quite early to make it in time. Funnily enough though I didn't drive the car all that much this trip because it was just too damn hot. While there were zero issues and running temps were nominal and the A/C was strong, RBs already run crazy hot as it is. Sure, it took it all like a champ but something about driving these cars in the ridiculous heat/humidity bothers me and makes me feel like I'm asking too much of it. I'm just me being weird and treating the car like a living thing with feelings; I'm mechanically sympathetic to a fault. Instead I was mainly driving something else around - a KX4(silver) 2001 X-Trail GT, that I acquired in May. There's a few different flavors to choose from with Xs, but visually it's the Nissan version of the Honda CR-V. Mechanically it's a whole different story as this, being the top-trim GT, has an SR20VET mated to a four-speed auto and full-time AWD! It was a very affordable buy in exceptional condition inside and out, with very low mileage...only 48k kms. Most likely it was owned by an older person who kept it garaged and well-maintained, so I'm really happy with how it all worked out. It literally needs zero attention at the moment, albeit except for some minor visual touch-ups. I wanted something quirky, interesting, and practical and for sure it handily delivers on all three of those aspects. I was immediately able to utilize the cargo and passenger capacity to its full extent. It's a lot of fun to drive and is quite punchy through 1st and 2nd. It's very unassuming -in the twisty bits it's a lot more composed than one would think at a glance- and it'll be even better once I get better tires on it(yes, it's an SUV but still a little boat-y for my liking). So...now I have two golden-era Nissans in silver. One sports car and one that does everything else; the perfect two-car solution I think👍 The rest of the trip...I was able to turn my stressed brain off and enjoy it, although I didn't quite get to do as much as I thought. I did some interesting things, met some interesting people, and happened into some interesting situations however, that's all for another post though only if people really want to know. Project-wise, I went back to Mine's again to discuss more plans and am hoping to wrap that up real soon; keep watching this space if that interests you. Additionally, while working in the tormenting sweatbox that is the warehouse, I was able to organize most of the myriad of parts that my friend is storing for me along with the cars, and the 34 has a nice little spot carved out for it: And since it can get so stupid hot in there, that made it all the more easy -after I was standing there looking at the car and said 'f**k it'- to finally remove all the damn gauges that have mostly been an eyesore all this time. Huzzah. The heat basically makes the adhesive backing on the gauge mounts more pliable to work with, so it was far less stressful getting this done. I didn't fully clean it up or chase the wiring though; that will happen once I have the car in closer possession. Another major reason to remove all that stuff is to give people less reasons to get in my car and steal s**t while it's being exported/imported when/if the time comes, which leads us to my next point... ...and that is even though it's time in Japan is technically almost up since it's a November car and the X would be coming in March, I'm still not entirely sure where my life and career is headed; I don't really know what the future looks like and where I'm going to end up. I feel there's a great deal of uncertainty with me and as a result of that, it feels like I'm at a crossroads moreso now than any point in my life thus far and there are some choices I need to make. Yes, I've had some years to consider things and prepare myself, however too much has happened in that time to maintain confidence and everything feels so up in the air; tenuous one might say. Simply put, there's just too much nonsense going on right now from multiple vectors. Admittedly, I'm struggling to stay in the game and keep my eyes on the prize. So much so in fact, that very recently I came the closest I ever have before to calling it quits outright; selling everything and moving on and not looking back. The astute among you will pick up on key subtext within this paragraph. In the meantime I've still managed to slowly acquire some final bits for the car, but it feels nice knowing there's not much left to get and I'm almost across that finish line; I have almost everything I'll ever want for my interpretation and expression on what it is I think an R34 should be. 'til later.
×
×
  • Create New...