Jump to content
SAU Community

Recommended Posts

hey guys, well i brought some Buddy Club PI's - 17 x 8 all round

got me some rubber, 235/45's - looks pretty sweet :P

but 1 problem....

centre caps?

don't the buddy's come with them? It looks sweet except for the missing centres - looks ****ed...

and on the rear of my GTS i have some shit sticking out of the centre about an ince or so - so i would need like dome centre caps for there...

i am wondering if I can get the centres? And if so where form? I don't mind haveing to buy them But i would have though you would get them with the rims :rofl:

thanks guys

Link to comment
https://www.sau.com.au/forums/topic/42794-buddy-club-dissapointment/
Share on other sites

I'm sorry to here about your lack of centres gatty but was just wondering if u can post some pics of your car with the new rims on it.

Give me a really good idea about how they would look on mine. Also how much did u pay and who did u get them off? PM me if would rather not make it public?

Gatty man, I got Buddy Club P1s on my line and they look sick.

If you wanted mags with centre cap, you should have brought something else.

They don't come with them.

But I can tell you not only are they lightweight, they are pretty strong too.

Mine did not bucked after a minor accident with the gutter, but got the sh$t scraped out of them :)

hmmm

i got them from http://www.modyourcar.com.au

17 x 8's all round cost 1500 to my door (+ or - 50 bucks)

i recomend them t anyone - i ordered on a Sunday - bank transfer on the Monday - recieved them on the Friday VIA courier service (from perth all the way to Qld!)

great job and I am going to order some more stuff through them!

my mags look great - just have to lower the front a inch now and it'll be sweet :D I will take some pics tomrorow after work and post them tomorrow afternoon - i will also do some close up's of the centre's so you guys can see what i mean :D

Guest INASNT
hmmm

i got them from http://www.modyourcar.com.au

17 x 8's all round cost 1500 to my door (+ or - 50 bucks)

i recomend them t anyone - i ordered on a Sunday - bank transfer on the Monday - recieved them on the Friday VIA courier service (from perth all the way to Qld!)

great job and I am going to order some more stuff through them!

my mags look great - just have to lower the front a inch now and it'll be sweet :( I will take some pics tomrorow after work and post them tomorrow afternoon - i will also do some close up's of the centre's so you guys can see what i mean :D

that site seems to have good prices on alot of things.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • @Murray_Calavera  If I were an expert I wouldn't be in here looking for assistance.  I am extremely computer literate, have above average understanding on how things should be working and how they should tie together.  If I need to go to a professional tuner so be it, but I'd much rather learn and do things myself even if it means looking for some guidance along the way and blowing up a few engines. @GTSBoy  I was hoping it would be as simple as a large vacuum leak somewhere but I'm unable to find anything, all lines seem to be well capped or going where they need to be, and when removed there is vacuum felt on the tube.  It would be odd for the Haltech built in MAP to be faulty, the GTT tune I imported had it enabled from the start, I incorrectly assumed it was reading a signal from the stock MAP, but that doesn't exist.  After running a vacuum hose to the ECU the signal doesn't change more than 0.2 in either direction.   I'll probably upload a video of my settings tomorrow, as it stands I'm able to daily drive, but getting stuttering when giving it gas from idle, so pulling away from lights is a slow process of revving it up and feathering the clutch until its moving, then it will accelerate fine.  It sounds like I need to get to the bottom of the manifold pressure issue, but the ignition timing section is most intimidating to me and will probably let a pro do that part.  Tomorrow I'll try a different vacuum line to T off of, with any luck I selected one that was already bypassed during the DBW swap. @feartherb26  I do have +T in the works but wanted to wait until Spring to start with that swap since this is my good winter AWD vehicle.  When removing the butterfly, did it leave a bunch of holes in the manifold that you needed to plug?  I thought about removing it but assumed it would be a mess.   I notice no difference when capping the vacuum line to it or letting it do its thing.  This whole thing has convinced me to just get a forward facing manifold when the time comes though.
    • Update: tested my spark plugs that are supposed to be 5ohms with a 10% deviation and one gave me a 0 ohms reading and the rest were 3.9ohm<, so one bad and the others on their way out.
    • 9" wheels are a little too wide for a RWD 32. They can fit. People have put R33 GTR wheels on 32s for years and years. But they are a very tight squeeze. This has been known for about 30 years. As I said - there is no difference between a 17 and an 18 in terms of what will fit. The rolling diameter needs to stay about the same as stock - not very much larger. If you increase that, you will start to have problems. If you increae rolling diamater at the same time as yo increase width, you will have problems earlier. as 9" wheels are pushing the boundaries already, you would need to be careful with tyre choice. I would put 8.5s on the front of mine, but would expect problems with 9s.
    • post up screen shots of your injector tables
    • Diagnostic flow for a code 21 says check signal at the ECU pins, on a voltmeter of some kind it should read 0.1V at idle, 0.12V cranking, 0.15-0.25V at 2000 rpm. Check each coil such that +1, -3 is infinite or very high resistance, -3, +2 should do the same. (-1, +3), (+3, -2), (+1, -2), and (-1, +2) should all be somewhere between 0 ohms and high resistance. If you trace the path from the coil pin all the way back to the ECU in the diagram the resistance you measure at the coil vs connected to the harness should be pretty much the same. 
×
×
  • Create New...