Jump to content
SAU Community

Recommended Posts

hey guys, well i brought some Buddy Club PI's - 17 x 8 all round

got me some rubber, 235/45's - looks pretty sweet :P

but 1 problem....

centre caps?

don't the buddy's come with them? It looks sweet except for the missing centres - looks ****ed...

and on the rear of my GTS i have some shit sticking out of the centre about an ince or so - so i would need like dome centre caps for there...

i am wondering if I can get the centres? And if so where form? I don't mind haveing to buy them But i would have though you would get them with the rims :rofl:

thanks guys

Link to comment
https://www.sau.com.au/forums/topic/42794-buddy-club-dissapointment/
Share on other sites

I'm sorry to here about your lack of centres gatty but was just wondering if u can post some pics of your car with the new rims on it.

Give me a really good idea about how they would look on mine. Also how much did u pay and who did u get them off? PM me if would rather not make it public?

Gatty man, I got Buddy Club P1s on my line and they look sick.

If you wanted mags with centre cap, you should have brought something else.

They don't come with them.

But I can tell you not only are they lightweight, they are pretty strong too.

Mine did not bucked after a minor accident with the gutter, but got the sh$t scraped out of them :)

hmmm

i got them from http://www.modyourcar.com.au

17 x 8's all round cost 1500 to my door (+ or - 50 bucks)

i recomend them t anyone - i ordered on a Sunday - bank transfer on the Monday - recieved them on the Friday VIA courier service (from perth all the way to Qld!)

great job and I am going to order some more stuff through them!

my mags look great - just have to lower the front a inch now and it'll be sweet :D I will take some pics tomrorow after work and post them tomorrow afternoon - i will also do some close up's of the centre's so you guys can see what i mean :D

Guest INASNT
hmmm

i got them from http://www.modyourcar.com.au

17 x 8's all round cost 1500 to my door (+ or - 50 bucks)

i recomend them t anyone - i ordered on a Sunday - bank transfer on the Monday - recieved them on the Friday VIA courier service (from perth all the way to Qld!)

great job and I am going to order some more stuff through them!

my mags look great - just have to lower the front a inch now and it'll be sweet :( I will take some pics tomrorow after work and post them tomorrow afternoon - i will also do some close up's of the centre's so you guys can see what i mean :D

that site seems to have good prices on alot of things.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • OK, Step 3, if you need to remove the valve body, either to replace it, the TCM, or to do a more complete drain.  First, you need to disconnect the TCM input wires, they are about half way up the transmission on the drivers side. One plug and the wires are out of the way, but there is also a spring clip that stops the socket from sliding back into the transmission. On my car the spring clip was easy to get, but the socket was really stuck in the o-ring of the transmission housing and took some.....persuasion. You can see both the plug to remove (first) and the spring clip (second) in this pic Incidentally, right next to the plug, you can see where the casting has allowance for a dispstick/filler which Nissan decided not to provide. there is a cap held on with a 6mm head bolt that you can remove to overfill it (AMS recommend a 1.5l overfill). Final step before the big mess, remove the speed sensor that is clipped to the valve body at the rear of the box.  Then removal of the Valve Body. For this the USDM Q50 workshop manual has a critical diagram: There are a billion bolts visible. Almost all of them do not need to be removed, just the 14 shown on the diagram. Even so, I both removed one extra, and didn't check which length bolt came from which location (more on that later....). Again it is worth undoing the 4 corners first, but leaving them a couple of turns in to hold the unit up....gravity is not your friend here and trans oil will be going everywhere. Once the corners are loose but still in remove all the other 10 bolts, then hold the valve body up with 1 hand while removing the final 4. Then, everything just comes free easily, or like in my case you start swearing because that plug is stuck in the casing. Done, the valve body and TCM are out
    • OK, so if you are either going for the bigger fluid change or are changing the valve body which includes the Transmission Control Module (TCM), first you should have both a new gasket 31397-1XJ0A and a torque wrench that can work down to 8Nm (very low, probably a 1/4 drive one). You can probably get by without either, but I really didn't want to pull it all apart together due to a leak. First, you now need that big oil pan. The transmission pan is 450 long x 350 wide, and it will probably leak on all sides, so get ready for a mess. There are 24x 6mm headed bolts holding the pan on. I undid the 2 rear corners, then screwed those bolts back in a couple of turns to let the pan go low at that end, then removed all the middle bolts on each side. Then, undo the front corner bolts slowly while holding the pan up, and 80% of the fluid will head out the rear. From there, remove the remaining bolts and the pan is off. You can see it is still dripping oil absolutely everywhere...it dripped all night.... I got another couple of litres when I removed the pan, and then another few when I removed the valve body - all up another 4l on top of the 3 already dropped in step 1.
    • Yeh I think i'll message an old contact i had for ages that manages his own tyre shop now.. n tell him what i want n work with him before ordering..  Got this 17x9 +30 Driftteks on 245/45/17 PSR Drag Radials on the rear.. They fit well - for your reference in future - Rear guards  have been lipped in & minimal to non flaring of the rear Gaurds.    
    • If only it were that easy! I also needed to remove seats, shocks, brake calipers, send my car through a fence, and use measuring and ended up guessing because I didn't remove seats, shocks and brake calipers. It can be hard sometimes Can be a little more complex than 'just measure' if you want to truly measure the entire wheel through all of it's suspension travel. But if you aren't going for every last mm then yeah, you can check the space you currently have and guesstimate.
    • If you own a car, and it has wheels on it, and you know the offset of those wheels, and you have a measuring device, you have everything you need to work out if other wheels will fit.
×
×
  • Create New...