Jump to content
SAU Community

Recommended Posts

Hello folks.

I am in Auckland New Zealand.

I need some help and advice I have a M35 bought second hand two years ago and added an extended warranty it has done 150k. I now have a diagnosed 'stretched' timing chain. The warranty co. (DriveRight via IAG NZ) is claiming this is 'wear and tear' and not covered. however the engine fault light is on, it stutters now as a result and could cause major internal damage if it breaks. Calling Nissan NZ, they say the chains 'shouldn't..but can stretch' and in their opinion it has failed as they should last for the lifetime of the vehicle with regular servicing.

Other Warranty companies (Like Autosure NZ) cover this replacement due to stretch. So in my view the component has failed. However DriveRight say it has not failed...yet!

The clincher of this is that DriveRight now know the part is 'faulty' and will not cover any damage as a result of continuing to drive. I'm stuck. The warranty clearly states this component is covered (Timing chain and Timing chain tensioners)...but we seem to have a disagreement on the interpretation of 'failure'.

Has anyone experienced this?
My bill is estimated to be $2500 to replace chain.

Cheers.

Technically it has not failed, the component is still in tact and has not lost any partial component of its primary construction or warn out to the point that it has failed.

Yes it is warn but it technically has not failed.

Just like a wheel bearing, just because its making a racket does not mean it has failed, it is just at the upper limit of its life span.

A failure would be indicated by a permenant non repairable failure of an integral component.

They are right by saying it is ware and Tare,

But Nissan identified this as a component failure as such.

You could also argue the term failure.

Does that mean complete failure to function OR partial failure to function

Which the latter is true. And you have a supported claim by the manufacturer.

Your dealing with an insurance company, they don't want to pay you.

So you need to be smart with terminology and build yourself a solid case.

I would use the term "failure" as your primary argument, because if it doesn't say complete failure, then it can also partially fail so technically it has failed.

If they are alleging the chain hasn't failed; by their own reasoning, there is no risk in continuing to drive the car.

They cannot play it both ways; it has either failed and requires replacement, or it is fine, and they must accept and repair any damage the chain does if/when it fails catastrophically.

They cannot hold you to ransom with an essentially undriveable vehicle. A catastrophic failure will cost much more than a chain replacement.

F**k them and their bullshit insurance speak.

You could ring Consumer (not sure if you have to be a member) - or "Fair Go" for advice on your rights.

For technical info see Soichi (ST Hytech) or Joe Kyle (Joe's Mechanical Services)- both Nissan experts

i left a message on the other forum, but i've recently replaced a chain also. they do stretch, but this is a 280+ km engine i done. I would class your situation as wear and tear, but then as said if they dont class it to be a failure and they do cover when it does fail they'll be up for a bigger bill to replace the motor than replacing a chain that is 'failing' according to manufacturer's assessment already.

So have you decided to get someone to replace it all now for $2.5k?

What shop is it in? Sounds like a lot of money. If you're not already there try and get a price on the phone from Soichi and Joe.

I need to make a call tomorrow morning on asking the mechanics to proceed with the replacement. Going to talk to the insurer one more.time now with my new information

Thanks all

a good mechanic who know's his way around a stagea, (most wont because they dont need this replacement done often) should be able to do the replacement in a full day. I used to work at nissan and got my parts at cost which was just over $700, retail was about $1k. The fluids need to be replaced, 5l of oil and coolant, you might as well get them to do a oil filter as well. And then the labour factor. So 2.5K is a bit but wouldnt say its to far off the right figure.

The small cam chains will require a lot of work to replace I think, as the cams may need to be removed... I would get them to replace the chain and guides only if that's what they diagnosed.

What were the symptoms, noisy chain slap?

What engine are we talking about?

The water pump can be easily changed without dropping the front of the engine, don't bother doing it now if it's still working.

I didnt do the secondary chains. They have tensioners to take up the slack and the chains are short enough that any wear would not cause any stretch issues like the primary.

I replaced my water pump while I was in there cause of the high k's. It was starting to show a bit of play and bearing noise. But if yous is fine I'd leave it in there, like what Scotty said.

Hello there,

well I thought I would give those interested a bit of an update.

After some extensive negotiations with the warrant company they have conceded that the chain (in my case) has FAILED.

This is excellent news as it means they are willing to front for the repair.

Still excluded in their view were the chain guides - as they thought they could be reused. I decided to still replace them.

So a lesson here for anyone reading in a similar position is...do not accept the first DECLINE or NO.

While the chains may have some 'wear' over the lifetime of an engine....they should not cause the engine to FAIL (In my case camshaft sensor fault and Stuttering engine, particularly on hills)

I appreciate your tips and advice and now have a puuuuuring Stagea again.

Cheers

Make sure they change the guides, especially the tensioner one. (known failure point as the plastic guide plate becomes brittle.)

I would say this may be the main cause of your issues, or perhaps the tensioner. If the chain has indeed 'stretched' or worn beyond what the tensioner can take the slack of, then I would be checking the oil feed squirters to the chain aren't blocked.

Hello there,

well I thought I would give those interested a bit of an update.

After some extensive negotiations with the warrant company they have conceded that the chain (in my case) has FAILED.

This is excellent news as it means they are willing to front for the repair.

Still excluded in their view were the chain guides - as they thought they could be reused. I decided to still replace them.

So a lesson here for anyone reading in a similar position is...do not accept the first DECLINE or NO.

While the chains may have some 'wear' over the lifetime of an engine....they should not cause the engine to FAIL (In my case camshaft sensor fault and Stuttering engine, particularly on hills)

I appreciate your tips and advice and now have a puuuuuring Stagea again.

Cheers

Look, I think NO is always the standard first response from these 3rd party warranty suppliers.

It's always worth fighting! If their initial response is NO; what's the worst that could happen?

Good to hear you stuck to your guns & got what you paid for.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
    • I checked spark on all cylinders and they all visually have spark with the plug pulled and grounded, but plug 1 is the only one that fouled. This was a running swap that blew up and was rebuilt by a machine shop, put a new wiring specialties harness and did all gaskets, studs, and bolts while it was out.  compression is 135-150 across all cylinders. Aside from that from my understanding with the z32 ecu and maf the car should start regardless. The wiring for TPS and the dual 02 sensor/ dual knock sensor stuff shouldn’t actually stop the car from starting or even running well, (just slightly rich)  they just give fault codes. Car supposedly is supposed to start as long as you have z32 afm and ecu with the nistune base map and that’s info coming from a well known and trusted tuner who does a lot with SR/RB (Rsenthalpy). After more trouble shooting today where I’m at right now is that the cas is sending signal to the injectors they click while spinning the rotor, Fuel pressure is now set at 43psi, all cylinders have good compression and all of the plugs looked great (just wet with fuel) except for cylinder 1 which was very black (cylinder 1 has 150psi compression). all of the coils generate spark if pulled out and grounded out on the head. On the fuel pump car just pops into the exhaust. On starting fluid car will fire off. Hard to tell if all cylinders are firing off but definitley a couple. sounds like all of them but it’s only for 3-5 seconds hard to tell. 
    • Final update!!! Got the front bar fitted and sprayed and all sorted now. My cutouts worked great and the indicators aren’t just falling off. 😂  
    • Is this a brand new LSD? if so, have you followed any break/bed in procedure for it? Usually involves heaps of figure 8 patterns, a fluid flush.
×
×
  • Create New...