Jump to content
SAU Community

Recommended Posts

There are pros and cons of each, the twins obviously keep a stock look under the engine bay however a single conversion does make any future work on the hot side of the engine bay much easier i.e. cheaper labour wise. No matter your option you will find a set-up that meets your requirements however value for money you can't go past the Garret GT2860R-5s, I PM you with a quote mid last week however only have one set left so if you're interested just let me know and I'll can put them to one side. If you wish to have a chat send me a PM with your mobile number and I'll give you a bell tomorrow.

If you need some factory twin manifolds, let me know. The pair I have are virually brand new.

sorry no complete kit.

as people chime inn you will probably make up the whole kit.

Edited by Stock e-Tune

Yes they are bigger than -5's but doubt you will make 600hp on them unless the rest of your motor is up to scratch. Tbh if ya after 600hp you're better off going the big single path and you might wanna stretch the budget a bit more!

My mobile is fully built standard cams and injectors but I have a power fc and will be upgrading injectors soon to 800cc I have a full exhaust system massive intercooler and pod filters have forged internals and what not I'm thinking -10s cos I can pump out more

I have complete Greddy THRUST TD05's with the option to go to larger TD06 SL2's kit from aircleaners to dumps 76 odd parts to this complete kit still in original boxes...never installed....had the Hi-mount manifold ceramic coated which cost a grand...8k for the kit

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Pads for R32 GTS-t, R32 GT-R non V-Spec (Sumitomo), R33 GTS-t and R34 GT-t are all interchangeable. R34 GT uses a 2x piston caliper, hence it didn't fit.
    • Checked with amayama and nope, the full S2 manual set is not available anymore. Unsurprising, but still disappointing as the ? on availability gave a glimmer of hope.
    • I've heard the Tomei USA head gaskets are decent if you want to o-ring the heads but otherwise not recommended.
    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
×
×
  • Create New...