Jump to content
SAU Community

Recommended Posts

Hi all,

So after 5 years with my 2003 v35 it starting to gradually breakdown.

My engine started overheating on the weekend which prompted me to bring my car to a JDM mechanic on Parramatta road.

Their diagnosis revealed:

1. Radiator was cracked and it needed replacing - Made sense, hence the reason why the car was over heating and blowing a bit of steam from the bonnet!

2. My front rotors and front/back pads were totally worn and need replacing - Did not make sense, as I got my front rotors and font/back pads replaced 2 years ago (July 2011) at a JDM mechanic based out West- cost me $1300 at the time. The car was on its original factory rotors/pads for a good 8 years before I replaced them.

The 'new' mechanic was adamant that the rotors in the car were the original factory ones and that there was no way they were replaced 2 years ago unless I drive with the brakes on (which I obviously don't). Apparently it is possible to sand down rotors to extend their life.

It appears one of the mechanics is doing a dodgy on me and I suspect it is the the original mechanic who installed the rotors/pads, as I suspect the current wants to milk me with an exxy radiator install ($790).

Is it possible that one of my mechanics is taking short cuts or diagnosing unecessary problems? Does anybody have experiences like this?

I think going forward I should request the receipt for all parts purchased instead of just the summary invoice provided by the mechanic.

Link to comment
https://www.sau.com.au/forums/topic/429857-dodgy-mechanics-experiences/
Share on other sites

1. $1300 for front rotors and a set of pads all round sounds overly expensive.

2. To save dollars Buy and install a new radiator yourself. (Very easy DIY)

With the quoted radiator install depends on the type of replacement radiator.

OEM rads are generally expensive and restrictive. Not worth replacing with OEM.

Aftermarket can be from $300 to $800. I suspect they will do a full check and service of your entire cooling system if your using radiator specialists like Natrad.

So a couple of choices.

1. Go to a dedicated brake shop and double check what both mechanics said/did. and get a quote while your there.

2. DIY the radiator or again go to a dedicated radiator specialist and get a quote.

If your a handy DIYer you could do the front rotors and all pads yourself.

Just take it to another mechanic or brake shop and ask them to check your brakes..

$1300 seems way over the top for front rotors and new pads all round.

$300 max for a pair of front rotors. (unless you got drilled/slotted rotors)

$100-150 for pads for each end.

parts total $600 max

Maybe 1 hour labour ($100-150).

extras (rags, cleanup, etc) - $50

Beer money for the boys - $500.

EDIT - if they did a fluid flush, that would be about another $100 max..

Edited by sonicii

An SAUer asked me for a name of my panelbeater/painter for his Bayside Blue R34 GT-R (formerly owned by me), so...

I recommended...

a) one at Yennora who does painting for bodyformaero and...

b) one at Emu Plains

Both of the above have painted Award-winning SAU Cars including Concours Awards

Anyway, "b" above has been slacking off!

The SAUer arrived with the car OK. But it didn't leave OK

> It had to be towed off to JapLink Motors for an engine rebuild.

> Intake valves were all bent

> They denied responsibility

> Car keys are placed on the front desk of the workshop for all to see and are not secured

> Shortly after, they sacked an apprentice

> SAUer Owner submitted a claim to Fair Trading

> JapLink accumulated all bills for a new engine, labour and tranfer of cams/gears

> Date of hearing was deferred

> Second hearing showed under questioning that the workshop had failed in its duty of care

> Tune originally done by Unigroup Eng was redone this time by DVS_JEZ - both Yavuz and Jez did great jobs, but more about that another time...

> Panelbeating Workshop has had to pay out!

I assume your around parramatta so i say go to another workshop with good reputation and have them check it. in ur area id send you to Team K Kustoms. and ask for Marcus. he's the owner and he works on the cars himself. top bloke and keeps costs as low as he can. he fixed my radiator and even found a cheap one for me rather than go oem and drain your budget.
and called me before ordering anything to make sure i was ok with costs


As for the price of rotors i know OEM will be double if not tripple of normal DBA rotors. so the new mechanic may just order oem or high grade just cus he doesan't know you or wants to make some extra $$$$

Team K Kustoms is on

23-25 Cowper St, Granville NSW 2142

Tel: 9682 5498

And like i said ask for Marcus and explain to him what happened and ask him to have a look over it .

Thanks for replies gents, its been a while since I've been on here, its a nice reminder of the 'community' vibe of this forum - enthusiasts helping eachother out.

To answer some questions:

DIY - Unfortunately I am not a DIY and don't have the time to learn (I'm flying out soon and need it fixed ASAP)

My location - I used to live out at Parramatta, now I'm based in the inner west (Drummoyne) - I would prefer something local, if anybody knows of good JDM mechanics around the inner west let me know.

Steam - The steam was coming from the front right hand side of my bonnest, presumably where the radiator is located.

Km's - I changed the rotors/pads at around the 51,000km mark........I am now at 66,000km. The orignal rotors/pads were good for at least 51,000km, not sure why the repalcements wore so quickly (unless they were never replaced i nthe first place!)

After letting my mechanic I know of another quote I got for the radiator replacent ($320 (radiator) + 220 (install) = $550), I received the following re-quote

Service oil + filter - $160

Read brake pads + disc machine - $240

Front pads + new front disc rotors - $360

Raditor replacement + collant service - $575

ABS solenoid and system reset - $325 (my park brake, slip and VDC lights are constantly on, hence the need for the system reset)

Total $1660

I am a reasonable guy and just want to pay market rate for what is being done

Do you think the above quote is reasonable? I am thinking of taking it somewhere else, but feel inclined to at least let them do the service as they did do the original diagnosis.

Cheers,


Danny

Danny, we're neighbours! I'm in Drummoyne also. Am just looking to buy my first V35 actually so I can't offer any specific experiences, sorry.

The only thing I will say though (based on experiences with other cars) is don't bother bargaining with mechanics too much. If you don't like the look of their quote, question it by all means, but it may be best to just go elsewhere for a 2nd. Don't play them off against each other either, or they'll get pissed off at the drop of a hat.

Another forum member suggested JLM in Rydalmere in another thread for V35's - formerly known as Japlink in Haberfield. Try them?

My intention wasn't to play them off against eachother.

When the mechanic didn't want to breakdown the cost of the radiator and install - thats what rang alarm bells and the impetus behind me getting another quote.

I was quated $790 for radiator + install which included a koyo radiator

A v35 Koyo radiator from an australian ebay seller was $290 + $220 install costs from another mechanic - $510

Thats a $280 price differential! As a prudent consumer, it was my obigation to investigate!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...